Wentzco F units
-
stephen neill
- Posts: 151
- Joined: Thu Jun 23, 2016 6:16 pm
Re: Wentzco F units
Here is a picture from the catalog showing what is included in a kit. You could buy kits as a dummy, single powered, or dual powered.
Steve
Steve
- Attachments
-
- _W1A0971.JPG (8.06 MiB) Viewed 6839 times
-
Carey Williams
- Posts: 690
- Joined: Sat Dec 24, 2016 3:10 pm
Re: Wentzco F units
Hello Brick lovers
Wentzco seems to have had a relatively short life .... no doubt cut shorter than anticipated with the introduction of the Atwater / GMC F units.
Wentzco ... first ad ( I could find ) MR April 1948 .... By June they tout immediate delivery ...which means in April it was not
The Honeymoon was short ..by March 1949 (feeling the lack of orders due to the now available Atwater units) ...ads appealing to those "value " minded... "Why pay the high price for die cast ?" .......hum because it looks better ? ....
Early 1950 Wentzo is pushing their power trucks ... by mid year they vanish
Dave / Scalecraft ... hope you are safe out there .... fires look awful ... If we could redirect Irma to drop a bit of rain out west ...
Cheers Carey
Wentzco seems to have had a relatively short life .... no doubt cut shorter than anticipated with the introduction of the Atwater / GMC F units.
Wentzco ... first ad ( I could find ) MR April 1948 .... By June they tout immediate delivery ...which means in April it was not
The Honeymoon was short ..by March 1949 (feeling the lack of orders due to the now available Atwater units) ...ads appealing to those "value " minded... "Why pay the high price for die cast ?" .......hum because it looks better ? ....
Early 1950 Wentzo is pushing their power trucks ... by mid year they vanish
Dave / Scalecraft ... hope you are safe out there .... fires look awful ... If we could redirect Irma to drop a bit of rain out west ...
Cheers Carey
-
Carey Williams
- Posts: 690
- Joined: Sat Dec 24, 2016 3:10 pm
Re: Wentzco F units
Thank you Bob for posting the nice photos of your early diesels .
Cheers Carey
Cheers Carey
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Wentzco F units
Thanks. Don't encourage me too much - everybody has seen my photos multiple times. I do have a new shot of the Scale Craft Mountain, soon to get barbeque black hosed on.
-
Carey Williams
- Posts: 690
- Joined: Sat Dec 24, 2016 3:10 pm
Re: Wentzco F units
Very nice Mountain Bob ...... did ScaleCraft use the same chassis on the full run of the Mountain ?..... There seems to have been a chassis change by ScaleCraft ..( perhaps when Donnelly fully took over) in 37 ..when Mountain was introduced. The earlier K4 and Hudson's had their chassis changed in late 1936 ...reading in the catalog ...you can see the changes ...and different motor mounting
here are catalog pages showing the early and late Hudson frames and motors.... the body casting also changed early two bumps on sand dome ..later one big bump ...and few other differences later ones do not seem to have the detail of the early ones ( in my opinion) ... and the later casting in the final version with the steam dome as a reverse switch .
Model Railroad ad from September 1936 announcing the Mountain.
Are those Central Locomotive Works PA's ? ... chrome ? very nice ....
Cheers Carey
here are catalog pages showing the early and late Hudson frames and motors.... the body casting also changed early two bumps on sand dome ..later one big bump ...and few other differences later ones do not seem to have the detail of the early ones ( in my opinion) ... and the later casting in the final version with the steam dome as a reverse switch .
Model Railroad ad from September 1936 announcing the Mountain.
Are those Central Locomotive Works PA's ? ... chrome ? very nice ....
Cheers Carey
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Wentzco F units
There are three styles of frames. The best ones have the worm separate from the motor, contained within two cast-on bearings. The convenient ones allow replacement of drivers as a wheelset. I have no idea what the sequence was.
I remember allusions in a Lobaugh catalog that somebody else used the Lobaugh Mountain to advertise theirs. That sure looks like a Lobaugh MT in the Scale Craft catalog.
I remember allusions in a Lobaugh catalog that somebody else used the Lobaugh Mountain to advertise theirs. That sure looks like a Lobaugh MT in the Scale Craft catalog.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Wentzco F units
On the PAs in the foreground - ATSF is a nickel-silver MTH. The brass one is the early CLW doorstop. As you can see, they need some "relief" carved into the radiator louvers. I am considering nickel plate, but so far have not found a willing plater with a low minimum charge. I may try one of those "do it yourself" deals.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: Wentzco F units
I will tell you this...and photos when I get back..this Wentzco box is small, no room for equalized trucks, motors, heck, wheels of any kind. Did it ever have sides? Not sure if there is even any room for four sides. It's tight.
Dave....gone by invitation
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Wentzco F units
A few more doorstops - one I am just marginally tolerant of is this Baldwin/Walthers/ maybe Adams FM 16-66:
And my Raymus E-7, which I have not yet soldered, is, as far as I am concerned, the epitome of Diesel doorstops. It has minor 'fit ' problems, probably curable with a bit more effort. Sure wish those match plates for the sides were available - I think we could use them on a lot of Adams doorstops!
And my Raymus E-7, which I have not yet soldered, is, as far as I am concerned, the epitome of Diesel doorstops. It has minor 'fit ' problems, probably curable with a bit more effort. Sure wish those match plates for the sides were available - I think we could use them on a lot of Adams doorstops!
- Attachments
-
- Raymus E7 002.jpg (1.19 MiB) Viewed 6747 times
- R.K. Maroon
- Posts: 3141
- Joined: Tue Feb 22, 2011 9:20 pm
Re: Wentzco F units
Bob -- Your FM diesel has a CLW heritage:
As sold with four-wheel trucks and 1500 HP it would be a H15-44. I have one of these but it is a total basket case -- somebody decided to clean up the steps with a die grinder, which only left me the job of cutting them off and fabricating replacements. Fun stuff indeed(!). I have always thought your version, with the very nice C&NW paint scheme and the six-wheel trucks, was fantastic. Please let me know if you ever have a hankering to trade -- doorstop for doorstop or otherwise! Note however that I would put a drive into it pronto and get it tooling around the club layout as fast as I could. It would of course have to be a CLW drive -- nothing else would be appropriate.
Jim
As sold with four-wheel trucks and 1500 HP it would be a H15-44. I have one of these but it is a total basket case -- somebody decided to clean up the steps with a die grinder, which only left me the job of cutting them off and fabricating replacements. Fun stuff indeed(!). I have always thought your version, with the very nice C&NW paint scheme and the six-wheel trucks, was fantastic. Please let me know if you ever have a hankering to trade -- doorstop for doorstop or otherwise! Note however that I would put a drive into it pronto and get it tooling around the club layout as fast as I could. It would of course have to be a CLW drive -- nothing else would be appropriate.
Jim
The link below any photo will display the image full size
-
Carey Williams
- Posts: 690
- Joined: Sat Dec 24, 2016 3:10 pm
Re: Wentzco F units
Hello Brick aficionados.
Bob thank you for posting the interesting engines ...who is Raymus ?
Jay was very kind to send some catalogs...( thank you ) ..which I'll scan and post .
Here we have some of the 1949 Wentzco catalog .... already feeling the heat from Atwater sales ...prices are slashed .
Even with slashed prices easy to see why Atwater / GMC walked away with the F unit market.
Brains and money behind Wentzco...John Wentz ...lawyer and builder of over 200 steam engines !!!! ok who has a Wentz steam engine ?
Cheers Carey
Bob thank you for posting the interesting engines ...who is Raymus ?
Jay was very kind to send some catalogs...( thank you ) ..which I'll scan and post .
Here we have some of the 1949 Wentzco catalog .... already feeling the heat from Atwater sales ...prices are slashed .
Even with slashed prices easy to see why Atwater / GMC walked away with the F unit market.
Brains and money behind Wentzco...John Wentz ...lawyer and builder of over 200 steam engines !!!! ok who has a Wentz steam engine ?
Cheers Carey
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Wentzco F units
Those did not show up on my befuddled iPad. Jack Raymus was a nice guy and doorstop nut who wanted slightly more detail than Adams was offering. I don't know what foundry he used or where his match plates went. I am happy with my piece of his history.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Wentzco F units
Finally showed up. The Adams units that I like are 17/64, I think, and miles ahead of these. Also, I bought an Atwater dummy F-7 in 1955 for $25, so even on the price front, Atwater won.
Now, even the Atwater is a doorstop!
Now, even the Atwater is a doorstop!
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: Wentzco F units
I probably need to get a clear shot of the outside of the box for dimensions.
These were in my files. There don't appear to be ends, just nose, roofs, frames, fuel tank covers and all sideframes in one small marked box.
You tell me. Could you just buy bits? No way to put drives, wheels and motors in this box.
These were in my files. There don't appear to be ends, just nose, roofs, frames, fuel tank covers and all sideframes in one small marked box.
You tell me. Could you just buy bits? No way to put drives, wheels and motors in this box.
- Attachments
-
- DSCN8762.JPG (401.56 KiB) Viewed 6678 times
-
- cropped sideframes.JPG (46.66 KiB) Viewed 6678 times
-
- BoxSideResize.JPG (105.42 KiB) Viewed 6678 times
-
- contentsResize.JPG (120.18 KiB) Viewed 6678 times
-
- BoxTopResize.JPG (105.46 KiB) Viewed 6678 times
Dave....gone by invitation
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 46 guests