Wentzco F units

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
stephen neill
Posts: 151
Joined: Thu Jun 23, 2016 6:16 pm

Re: Wentzco F units

Postby stephen neill » Wed Sep 06, 2017 9:23 am

Here is a picture from the catalog showing what is included in a kit. You could buy kits as a dummy, single powered, or dual powered.
Steve
Attachments
_W1A0971.JPG
_W1A0971.JPG (8.06 MiB) Viewed 6842 times

Carey Williams
Posts: 690
Joined: Sat Dec 24, 2016 3:10 pm

Re: Wentzco F units

Postby Carey Williams » Wed Sep 06, 2017 3:31 pm

Hello Brick lovers

Wentzco seems to have had a relatively short life .... no doubt cut shorter than anticipated with the introduction of the Atwater / GMC F units.

Wentzco ... first ad ( I could find ) MR April 1948 .... By June they tout immediate delivery ...which means in April it was not

The Honeymoon was short ..by March 1949 (feeling the lack of orders due to the now available Atwater units) ...ads appealing to those "value " minded... "Why pay the high price for die cast ?" .......hum because it looks better ? ....

Early 1950 Wentzo is pushing their power trucks ... by mid year they vanish

Dave / Scalecraft ... hope you are safe out there .... fires look awful ... If we could redirect Irma to drop a bit of rain out west ...

Cheers Carey

IMG_5430.JPG
IMG_5430.JPG (1.79 MiB) Viewed 6826 times
IMG_5431.JPG
IMG_5431.JPG (1.55 MiB) Viewed 6826 times
IMG_5432.JPG
IMG_5432.JPG (1.52 MiB) Viewed 6826 times
IMG_5433.JPG
IMG_5433.JPG (1.7 MiB) Viewed 6826 times

Carey Williams
Posts: 690
Joined: Sat Dec 24, 2016 3:10 pm

Re: Wentzco F units

Postby Carey Williams » Wed Sep 06, 2017 11:52 pm

Thank you Bob for posting the nice photos of your early diesels .
Cheers Carey

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Thu Sep 07, 2017 1:04 am

Thanks. Don't encourage me too much - everybody has seen my photos multiple times. I do have a new shot of the Scale Craft Mountain, soon to get barbeque black hosed on.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Thu Sep 07, 2017 1:57 am

Here you go:
image.jpg
image.jpg (614.53 KiB) Viewed 6810 times

Carey Williams
Posts: 690
Joined: Sat Dec 24, 2016 3:10 pm

Re: Wentzco F units

Postby Carey Williams » Thu Sep 07, 2017 12:29 pm

Very nice Mountain Bob ...... did ScaleCraft use the same chassis on the full run of the Mountain ?..... There seems to have been a chassis change by ScaleCraft ..( perhaps when Donnelly fully took over) in 37 ..when Mountain was introduced. The earlier K4 and Hudson's had their chassis changed in late 1936 ...reading in the catalog ...you can see the changes ...and different motor mounting

here are catalog pages showing the early and late Hudson frames and motors.... the body casting also changed early two bumps on sand dome ..later one big bump ...and few other differences later ones do not seem to have the detail of the early ones ( in my opinion) ... and the later casting in the final version with the steam dome as a reverse switch .

Model Railroad ad from September 1936 announcing the Mountain.

Are those Central Locomotive Works PA's ? ... chrome ? very nice ....

Cheers Carey
IMG_4405.JPG
IMG_4405.JPG (2.76 MiB) Viewed 6792 times
IMG_4272.JPG
IMG_4272.JPG (1.56 MiB) Viewed 6792 times
IMG_4399.JPG
IMG_4399.JPG (1.43 MiB) Viewed 6792 times
IMG_4271-2017-07-08_11-50-19-951.JPG
IMG_4271-2017-07-08_11-50-19-951.JPG (2.09 MiB) Viewed 6792 times
IMG_4269.JPG
IMG_4269.JPG (2.02 MiB) Viewed 6792 times
IMG_4402.JPG
IMG_4402.JPG (1.3 MiB) Viewed 6792 times

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Thu Sep 07, 2017 2:00 pm

There are three styles of frames. The best ones have the worm separate from the motor, contained within two cast-on bearings. The convenient ones allow replacement of drivers as a wheelset. I have no idea what the sequence was.

I remember allusions in a Lobaugh catalog that somebody else used the Lobaugh Mountain to advertise theirs. That sure looks like a Lobaugh MT in the Scale Craft catalog.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Thu Sep 07, 2017 2:07 pm

On the PAs in the foreground - ATSF is a nickel-silver MTH. The brass one is the early CLW doorstop. As you can see, they need some "relief" carved into the radiator louvers. I am considering nickel plate, but so far have not found a willing plater with a low minimum charge. I may try one of those "do it yourself" deals.

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Wentzco F units

Postby ScaleCraft » Thu Sep 07, 2017 8:24 pm

I will tell you this...and photos when I get back..this Wentzco box is small, no room for equalized trucks, motors, heck, wheels of any kind. Did it ever have sides? Not sure if there is even any room for four sides. It's tight.
Dave....gone by invitation

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Thu Sep 07, 2017 11:51 pm

A few more doorstops - one I am just marginally tolerant of is this Baldwin/Walthers/ maybe Adams FM 16-66:

FM 16-66 doorstop.jpg
FM 16-66 doorstop.jpg (1.07 MiB) Viewed 6750 times


And my Raymus E-7, which I have not yet soldered, is, as far as I am concerned, the epitome of Diesel doorstops. It has minor 'fit ' problems, probably curable with a bit more effort. Sure wish those match plates for the sides were available - I think we could use them on a lot of Adams doorstops!
Attachments
Raymus E7 002.jpg
Raymus E7 002.jpg (1.19 MiB) Viewed 6750 times

User avatar
R.K. Maroon
Posts: 3141
Joined: Tue Feb 22, 2011 9:20 pm

Re: Wentzco F units

Postby R.K. Maroon » Fri Sep 08, 2017 12:51 am

Bob -- Your FM diesel has a CLW heritage:

CLW FM H15-44.JPG
CLW FM H15-44.JPG (53.53 KiB) Viewed 6743 times


As sold with four-wheel trucks and 1500 HP it would be a H15-44. I have one of these but it is a total basket case -- somebody decided to clean up the steps with a die grinder, which only left me the job of cutting them off and fabricating replacements. Fun stuff indeed(!). I have always thought your version, with the very nice C&NW paint scheme and the six-wheel trucks, was fantastic. Please let me know if you ever have a hankering to trade -- doorstop for doorstop or otherwise! Note however that I would put a drive into it pronto and get it tooling around the club layout as fast as I could. It would of course have to be a CLW drive -- nothing else would be appropriate.

Jim
The link below any photo will display the image full size

Carey Williams
Posts: 690
Joined: Sat Dec 24, 2016 3:10 pm

Re: Wentzco F units

Postby Carey Williams » Sat Sep 09, 2017 6:16 pm

Hello Brick aficionados.

Bob thank you for posting the interesting engines ...who is Raymus ?

Jay was very kind to send some catalogs...( thank you ) ..which I'll scan and post .

Here we have some of the 1949 Wentzco catalog .... already feeling the heat from Atwater sales ...prices are slashed .

Even with slashed prices easy to see why Atwater / GMC walked away with the F unit market.

Brains and money behind Wentzco...John Wentz ...lawyer and builder of over 200 steam engines !!!! ok who has a Wentz steam engine ?
Cheers Carey

1949 catalog cover.jpg
1949 catalog cover.jpg (1.03 MiB) Viewed 6703 times
1949 page 1-2.jpg
1949 page 1-2.jpg (1.66 MiB) Viewed 6703 times
1949 page 3-4.jpg
1949 page 3-4.jpg (1.63 MiB) Viewed 6703 times
1949 page 5-6.jpg
1949 page 5-6.jpg (1.64 MiB) Viewed 6703 times

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Sat Sep 09, 2017 8:58 pm

Those did not show up on my befuddled iPad. Jack Raymus was a nice guy and doorstop nut who wanted slightly more detail than Adams was offering. I don't know what foundry he used or where his match plates went. I am happy with my piece of his history.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Wentzco F units

Postby bob turner » Sat Sep 09, 2017 9:02 pm

Finally showed up. The Adams units that I like are 17/64, I think, and miles ahead of these. Also, I bought an Atwater dummy F-7 in 1955 for $25, so even on the price front, Atwater won.

Now, even the Atwater is a doorstop!

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: Wentzco F units

Postby ScaleCraft » Sat Sep 09, 2017 10:16 pm

I probably need to get a clear shot of the outside of the box for dimensions.
These were in my files. There don't appear to be ends, just nose, roofs, frames, fuel tank covers and all sideframes in one small marked box.
You tell me. Could you just buy bits? No way to put drives, wheels and motors in this box.
Attachments
DSCN8762.JPG
DSCN8762.JPG (401.56 KiB) Viewed 6681 times
cropped sideframes.JPG
cropped sideframes.JPG (46.66 KiB) Viewed 6681 times
BoxSideResize.JPG
BoxSideResize.JPG (105.42 KiB) Viewed 6681 times
contentsResize.JPG
contentsResize.JPG (120.18 KiB) Viewed 6681 times
BoxTopResize.JPG
BoxTopResize.JPG (105.46 KiB) Viewed 6681 times
Dave....gone by invitation


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 51 guests