O scale a rich's mans hobby circa 1946

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
Rufus T. Firefly
Posts: 42236
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: O scale a rich's mans hobby circa 1946

Postby Rufus T. Firefly » Fri Apr 07, 2017 1:48 pm

ScaleCraft wrote:
Rufus T. Firefly wrote:
Difficult is finding live wire splices in the wall between the studs in the house I'm renovating when there are receptacles inside the walls....and it's all soldered together 12/2.


True. Knob and Tube...soldered and taped....and you haven't lived until 60 year old solder joints start failing, overheating, and you get fire in the wall.

Got rid of the last Knob and Tube in this place 40 years ago, and some of those "joints" were scary.


It's not knob & tube.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

Seaboard Air Line Fan
Posts: 1308
Joined: Mon Mar 08, 2004 9:49 pm
Location: Virginia

Re: O scale a rich's mans hobby circa 1946

Postby Seaboard Air Line Fan » Fri Apr 07, 2017 3:03 pm

ScaleCraft wrote:
Chris Rock wrote:
ScaleCraft wrote:And there you go. How would you wire those reverse loops in three rail?


In 3 rail you solder some wires to the rails.
In 2 rail you solder some wires to the rails through a reverser.
Neither is difficult.



Depends on whether you have switches or not. And have to have live frogs....or jumper around....
AC in to a transformer. Find and wire in a rectumfrier. Add fuses. Wire in reverse switch. Connect to two rails...oh, wait, once I get past the switch, what happens now?.

Or, plug your ZW in and clip the lockon onto the rails.

We can argue this all day long.

Then in 2-rail you have common ground....or not.
Now what....if not, do you have separate reverse for each block, or just cab controls?
If a block is reversed from the next, what do you do to deal with that?
Three rail never an issue.

In fact you can plug a whole bunch of power packs in and connect them to blocks in 3-rail...and as long as you polarize the commons....



I had a reverse loop when I was in HO last century. I had the loop and the main wired to a DPDT switch and when the train got into the loop I flipped the switch, thereby changing the polarity of the main. I think I used Atlas switches, didn't seem too complicated back then.


All this talk about wiring is re-affirming my decision to go BPRC :mrgreen:
BobD aka Drifty

The Crow Flies At Midnight

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: O scale a rich's mans hobby circa 1946

Postby ScaleCraft » Fri Apr 07, 2017 3:18 pm

Rufus T. Firefly wrote:
ScaleCraft wrote:
Rufus T. Firefly wrote:
Difficult is finding live wire splices in the wall between the studs in the house I'm renovating when there are receptacles inside the walls....and it's all soldered together 12/2.


True. Knob and Tube...soldered and taped....and you haven't lived until 60 year old solder joints start failing, overheating, and you get fire in the wall.

Got rid of the last Knob and Tube in this place 40 years ago, and some of those "joints" were scary.


It's not knob & tube.

Usually a hallmark of such is soldered and taped connections.
Amazing that it is not Knob and Tube, yet soldered.
Call Mike Holmes.
Dave....gone by invitation

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: O scale a rich's mans hobby circa 1946

Postby ScaleCraft » Fri Apr 07, 2017 3:24 pm

Seaboard Air Line Fan wrote:
I had a reverse loop when I was in HO last century. I had the loop and the main wired to a DPDT switch and when the train got into the loop I flipped the switch, thereby changing the polarity of the main. I think I used Atlas switches, didn't seem too complicated back then.


All this talk about wiring is re-affirming my decision to go BPRC :mrgreen:


It's not too complicated once you understand the principle. Complex trackage makes it fun to determine where you reverse power. I know of one 2-rail 0 pike that has a reverse loop built into a huge, long, curving grade that passes over itself...with a reverse section off of it halfway up...and few could figure it out.
Grade goes from one lower portion to an upper portion.
Then he has a reverse section in a yard between the sides of the double tracked mainline.....and the gaps aren't even marked. I guarantee you would not be able to traverse it first or second time.

Yet, big 3-rail pikes, never had any issue ever finding where the reversing section was.

Must have had some dcc auto reversing section installed.

Of course, in some instances, you need to remember where the reverse switches were set last time. Hence the suggestion for a red signal across the gap.
Dave....gone by invitation

User avatar
rogruth
Posts: 24452
Joined: Sun Aug 14, 2005 8:32 pm
Location: pembroke,ga

Re: O scale a rich's mans hobby circa 1946

Postby rogruth » Sat Apr 08, 2017 12:05 am

1948 through July, 1952 I had a 2 rail DC HO layout and a 3 rail AC O layout. The O layout started in 1946 and the HO in 1948 and both came down in 1952 when I went to college. This is before any type of command control and I did not have problems wiring and running either layout. Those younger than me
shouldn't have any trouble with this stuff as they have had much more exposure to electronic stuff than I ever had.
There doesn't seem to be a huge price difference between scales if you stay at certain levels and not compare Kias and Panameras.
roger

I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: O scale a rich's mans hobby circa 1946

Postby sarge » Sat Apr 08, 2017 9:17 am

ScaleCraft wrote:Depends on whether you have switches or not. And have to have live frogs....or jumper around....
AC in to a transformer. Find and wire in a rectumfrier. Add fuses. Wire in reverse switch. Connect to two rails...oh, wait, once I get past the switch, what happens now?.

Or, plug your ZW in and clip the lockon onto the rails.

We can argue this all day long.


OK, only one example of apples and oranges and (Bob D -Grin!) grapes. Since we've successfully hijacked poor Carey's thread into a debate about Dems and Repub- no sorry two-rail power, three-rail-power, battery, some thoughts.

First off, I'm using Dave's argument above only illustrate a point, not to argue with or slam Dave. Everyone who champions some sort of blind fealty to a control system does this, though. "(Your foolish choice), Get a shovel and dig up some selenium and copper and iron, scratchbuild a power supply, go through every detail or (my superb choice of religion) just hook up two wires/a lockon/a battery and bask in my intellectual magnificence." The problem with it all is, first off, its not a valid comparison and, second off, someone will follow it seeking enlightenment and really discover they've been had.

The valid comparison point is this. It is easier to hook up two wires than to wire in any control system properly. If you compare a well-done installation to a well-done installation, many of the arguments for one or the other fall away, two of which are ease of operator use and reliability.

A properly done model railroad control system never requires just two wires. (Scace's Fifth Law of Model Railroading). That means your deadrail prayer group too, Delridge, so stop raising your hand and going "Ooh oooh! Pick Me!" Grin!

I can take you down to my cellar and throw the switches on my layout after a year's slumber (It's happened due to a combination of things like the mag, health, aged parents) and I know it will run flawlessly even with the cobwebs. It's two rail traditional DC. Why? I took the time to do the installation properly, busses, drops, feeds, real toggles and rotaries (not that Chinese miniaturised crap from MR adverts or Radio Shack), soldered joints with expansion joints, the whole schtick.

My previous layout was the same way, that one DCC. No two-wires to the rails crap, a hot-loop buss, all the same things and all the same care. Anyone that tells you DCC needs somehow less wiring to do it properly is giving you a reach-around from behind. "Proper" equals isolation blocks, feeds and drops, wiring the turnouts properly, and you get apples to apples. Add to it your decoder installation. You are doing it yourself, aren't you?

Three rail? When we first got married, my wife was very much into Dept. 56 collecting. So, why not crack out my old Hornby and Lionel and build a layout for her to display these things? A large layout in three rail (sorry, Dave, but the bullshit flag thrown here) needs every bit the same amount of care and wiring expended. I'll be honest, three-rail wiring for reliable operation was about as non-intuitive for me after decades of two-rail as two-rail wiring is to the Hirail crowd. I had to crack out an old Fawcett Crest handbook (remember those) and teach myself how to think three-rail. Not hard, but different.

I venture to guess the vast majority of whinging three-railers get on about regarding their TMCC or DCS not working to expectation is due to the "two wire" myth, then they get all bristly when they have to buy a Barry book that tells 'em how to do it right. It's easier to blame the system (and repeat the two-rail is so very hard myth while they're at it). Do it properly, and apples to apples.

Your turn, Bob. Battery RC is on the surface easy. No wires, no toggles, no insulated rail, what could be simpler? Ha! I've gone down this road, too, so the dirty petticoats the deadrail people carefully hide can be outed. Your wiring is still there, just under the shell rather than in the fascia of the layout. Unless you're checkbooking it, you wire each loco with the complete control system and power supply in miniature. You can slap it in or you can do it properly without an isolation toggle and a recharge point sticking out the side ruining the appearance of the loco. Solder your rail too or do something to make the joint alignments robust. Mechanical, not electrical, but still needs addressed. Soldered or otherwise proper robust joints can't only be laid at the feet of the trackpower people. It might be even more important for you, since your stuff can go crawling off like a drunk after closing, un-noticed until the dreaded Thump of Death is heard from the aisle and do it under power. Just a couple examples, but properly done installations aren't quite a simple as the mythology and evangelism would have the rest of us believe. Solid construction of the trackwork, robust installation of the receiver, power, and modulating circuitry makes for reliability, appearance can be destroyed by poor placement of recharging ports and off/on toggles, yep, battery R/C works fine, but that work needs done to bring it up to a comparable level with any other properly done control system. I've seen it done well, and I've done it in O and #1 myself, so the ease and simplicity bit (and Tammy Fae crying real tears of rapture) is a bit wasted on me.

So, understanding three-rail is not difficult for a guy who came up in two-rail, but it has its foibles you need to learn to do it properly.

The reversed case is just as true to do two rail properly, but it isn't any "harder".

DCC is no easier than DC to do properly and you get sound out of the deal if that's important to you, but you get to learn loco installs or buy them and pay for the maintenance too because you bought the install and have no idea how to repair it. Personal choice there.

Same for three-rail vs command. Properly done it works reliably, and you get sound as a payoff for the additional work of the electronics in the loco. Again you either add that task or you give up some independence by checkbooking installs and repairs because you have no idea how to fix what was installed by Chinese girls or your DCS guy.

Battery R/c, you give up some failsafes or at least need to think about how to keep locos on the rail, out of the aisles, and off each other but the independence of each loco is the real gain you get for that new risk. Sound is there, but either way you are wiring it up each and every loco or checkbooking and casting your independence to your installer both to put it in (neatly, properly robust, and invisibly, we hope) and to replace a battery pack or two if they start not taking charges. Don't forget to plug it in, be comfy with the notion you are recharging batteries when you are elsewhere so if $hit goes wrong it goes way wrong (a paranoia I have even when recharging a tablet or a phone).

The upshot is each system choice in my view has tradeoffs and advantages that make each person's choice validly their own. None of them are the future to the exclusion of any other. Properly done, and you are now bloody sick of seeing the word here but that is the key to this premise, but properly done each is pretty involved and will give reliable and mostly intuitive control. None are harder or easier for a layout beyond the simple loop, they all require thought, care, and understanding to make work well and you never ever only "hook up two wires and go."

Seaboard Air Line Fan
Posts: 1308
Joined: Mon Mar 08, 2004 9:49 pm
Location: Virginia

Re: O scale a rich's mans hobby circa 1946

Postby Seaboard Air Line Fan » Sat Apr 08, 2017 11:52 am

Sarge...I think you have it covered :!:

Here's the minor issues I have with battery power:

1) Unless I keep track of how long I run the engine each time, I'm only guessing at how much "juice" I have left before I have to recharge. From extensive testing I know I get approx 2-1/2 hours of run time on the 2000Mah NiMh or 2200 LiPo batteries. When the voltage gets low the engine stops. When the 9v battery in the transmitter gets low, the LED on the Tx blinks. It takes approx 2 hours to recharge a battery. I ran an engine (Weaver 4-6-0 chassis on a homemade boiler) for 30 minutes yesterday that was last charged in Nov 2016 and it still has a charge left in it. All of my steamers have the charging jack under the removable coal load or under the tender. I've BPRC'd a Williams E7 which has the charging jack in the rear door and a Weaver RS3 which has it mounted on the fuel tank. Both these engines currently use the BlueRail bluetooth board vice the Deltang Rx. I also have the BlueRail board in a G-scale Bachmann 4-6-0. I use my Ipad for the transmitter.

2) No sound. Well, I did have 1 with sound but it was very generic (a MyLocoSounds board). The only sounds I would like to have is steam chuff and diesel sound. I found I hardly ever used the bell/whistle/horn when I used TMCC or DCS. The other sounds they provide are fluff. All-in-all I really don't miss the sounds as the train going around the layout makes plenty of "noise" as it is. I actually like less sound because now I can hear what the engine is doing, the sounds mask potential issues.

3) Availability, I simply can't go to the LHS and get my fix. My first purchases came from RCS Australia (Tony Walsham). Tony offered a great product based on the Deltang Tx and Rx, but he no longer offers the Rx I used. I found a guy in the US, but he only ordered them from the manufacturer (Deltang) in the UK and then sent them to me. I finally found a place (RCTrains) in the UK that offers them at good prices with wiring already on the board so it can be connected without having to solder onto the board itself. These Deltang receivers have been bullet proof so far (going on 3 years) and the transmitters have been too.

While cost isn't huge, converting an engine that has a good running system already inside is not cheap. I did manage to get $50 each on trade in of my old PS2 electronics. Best engines are old, conventional engines like Williams brass.


What I didn't like about DCS/TMCC was the sheer volume of information given out. Between the MTH manual and Barry's Bible we're talking of 500+ pages (the TMCC instructions were only a few pages), add to that all the gibber-jabber on the forums that doesn't make it into a book. Often than not I found myself asking "What aren't they telling me?". Also, it seems like wiring a command control system is layout dependent, no 2 layouts are wired the same. Nature of the beast I guess, but confusing to the newbie (and the old vet) trying to figure out why his trains don't run.

I have more to say but have to get ready to go to work at the GC, more later I'm sure!
BobD aka Drifty

The Crow Flies At Midnight

Carey Williams
Posts: 690
Joined: Sat Dec 24, 2016 3:10 pm

Re: O scale a rich's mans hobby circa 1946

Postby Carey Williams » Sat Apr 08, 2017 3:05 pm

Glad to see Don Rickles is alive and well "channeling" through Sarge .

This is good stuff ..get this man a microphone and spot light .

"deadrail prayer group"


" since your stuff can go crawling off like a drunk after closing"

"because you have no idea how to fix what was installed by Chinese girls or your DCS guy.


I'm sure all of the proud high bidders today at Seacrest's mega auction will be turning to you for guidance, praise, and wisdom with what to do with their new purchases.

Two wires seem to work fine on Topsy ...
https://en.wikipedia.org/wiki/Topsy_(elephant)

Everyone has an opinion... which is great ..this would be a boring world if we all agreed the sky was blue.

as I was saying

November 1946 Varney introduces the (O gauge) ten wheeler in a metal box ..you supply screw driver .....$100.00
Mantua's "Belle of the 1890's" ( ten wheeler ) 29.95 stick on track and go .....

or broken down at a per wheel cost of
O gauge : $10.00 per wheel
HO gauge : $2.95 per wheel


No matter how many wires used, you can not reverse loop the bottom line .
Cheers Carey


link to actual use of two wires and a reversing finger ....
https://www.youtube.com/watch?v=prwn04aGsIg

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: O scale a rich's mans hobby circa 1946

Postby sarge » Sat Apr 08, 2017 3:49 pm

After a little snipping without (hopefully) taking you out of context:

Carey Williams wrote:as I was saying

November 1946 Varney introduces the (O gauge) ten wheeler in a metal box ..you supply screw driver .....$100.00
Mantua's "Belle of the 1890's" ( ten wheeler ) 29.95 stick on track and go .....

or broken down at a per wheel cost of
O gauge : $10.00 per wheel
HO gauge : $2.95 per wheel

No matter how many wires used, you can not reverse loop the bottom line.


Oh yes, but I can-Grin!

Varney ten wheeler: $100
Mantua Belle of the 90s: $29.95

Broken down at a per unit area cost

O gauge: $100
HO Guage $119.80

I won't mention the Varney at least has a prototype, will be fun to build, and will run. The Mantuas are Petticoat Junction cutesy, no fun of the build, and ran terribly in comparison. They might be more an example of why old O scalers didn't flock en masse to HO. There was and is more to ones notion of "value" than price.
Last edited by sarge on Sat Apr 08, 2017 4:14 pm, edited 1 time in total.

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: O scale a rich's mans hobby circa 1946

Postby sarge » Sat Apr 08, 2017 4:12 pm

Carey Williams wrote:Glad to see Don Rickles is alive and well "channeling" through Sarge .

This is good stuff ..get this man a microphone and spot light .

"deadrail prayer group"


" since your stuff can go crawling off like a drunk after closing"

"because you have no idea how to fix what was installed by Chinese girls or your DCS guy.


I'm sure all of the proud high bidders today at Seacrest's mega auction will be turning to you for guidance, praise, and wisdom with what to do with their new purchases.

Two wires seem to work fine on Topsy ...
https://en.wikipedia.org/wiki/Topsy_(elephant)

Everyone has an opinion... which is great ..this would be a boring world if we all agreed the sky was blue.


link to actual use of two wires and a reversing finger ....
https://www.youtube.com/watch?v=prwn04aGsIg


Its time to bow out of the discussion at this point, since how I might turn a phrase has become a matter of belittlement rather than the source of at least a grin as intended. That's always a good indicator that things have gone passed the exchange of ideas and it's time to move on.

User avatar
rogruth
Posts: 24452
Joined: Sun Aug 14, 2005 8:32 pm
Location: pembroke,ga

Re: O scale a rich's mans hobby circa 1946

Postby rogruth » Sat Apr 08, 2017 6:20 pm

Sarge,
It was good to have you back at least for a short while.
roger

I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH

J. S. Bach
Posts: 5820
Joined: Wed May 16, 2007 9:30 pm

Re: O scale a rich's mans hobby circa 1946

Postby J. S. Bach » Sat Apr 08, 2017 8:19 pm

I have no interest in battery power as I like to sit back and watch the trains run for long periods. One time I set a train on my DC Central and let it run for five or six hours. All fun.

User avatar
rogruth
Posts: 24452
Joined: Sun Aug 14, 2005 8:32 pm
Location: pembroke,ga

Re: O scale a rich's mans hobby circa 1946

Postby rogruth » Sat Apr 08, 2017 8:30 pm

J. S. Bach wrote:I have no interest in battery power as I like to sit back and watch the trains run for long periods. One time I set a train on my DC Central and let it run for five or six hours. All fun.

Dave,
I like that also but my longest was only about two hours.
roger

I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: O scale a rich's mans hobby circa 1946

Postby bob turner » Sat Apr 08, 2017 9:33 pm

Me too, but about six laps is all I can watch at one time, even with a mint julep.

User avatar
De Bruin
Posts: 992
Joined: Thu Jan 12, 2017 8:24 pm

Re: O scale a rich's mans hobby circa 1946

Postby De Bruin » Sun Apr 09, 2017 12:51 am

Attention Span -
Operation - 150 minutes
Continuous running - 15 minutes tops (save running failures) no matter what is on, you know "Attention Deficit Disorder."

I liked the way Sarge distinguished between Model Railroaders and Railroad Modelers, I am clearly in the later category by practice, if not end product.
My "Track-World" layout is a barren place devoid of color and operation at least for now, in fact more like a slot car track, at least on the one end where I super-elevated the curves.

Say how 'bout that Stout Auction today for Jim Seacrest's estate? Any good stories out there?
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 53 guests