Machine Shop / Locomotive Drive Work

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
Chris Webster
Posts: 956
Joined: Mon May 25, 2015 8:25 pm

Re: Machine Shop / Locomotive Drive Work

Postby Chris Webster » Fri Oct 30, 2026 7:10 pm

R.K. Maroon wrote:. I reviewed Bob's notes on setup and came up with a slightly different approach, which was to leave the universal joint in place and replace the ball-and-socket with a section of rubber tubing. I can report that the reputation of Toyota vacuum hose is intact -- it was just what was needed.


I recently purchased a non-running 0-4-0. The pictures showed there wasn't any connection between the gearbox and motor so I figured it would would be an easy fix, requiring about a 1.5 inch long piece of Toyota O tubing.

However, after receiving the 0-4-0, I realized there is nothing to hold the axle-mounted gearbox stationary relative to the frame - is that normal? Will the Toyota tubing by itself be enough to prevent the entire gearbox from rotating?

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Machine Shop / Locomotive Drive Work

Postby bob turner » Fri Oct 30, 2026 7:33 pm

Depends.

Think of a lever - that is what the worm shaft is. It should have decent bearings on each end of the worm - those bearings absorb torque and the vertical thrust from the worm gear.

The longer the worm shaft, the less lateral force on the Toyota tube. But if you make the distance between motor shaft and worm shaft very small, the hose can withstand forces from a shorter wormshaft.

Picture if you need it - but I would have to add it to my Shutterfly account.

Chris Webster
Posts: 956
Joined: Mon May 25, 2015 8:25 pm

Re: Machine Shop / Locomotive Drive Work

Postby Chris Webster » Fri Nov 06, 2026 10:58 pm

bob turner wrote:The longer the worm shaft, the less lateral force on the Toyota tube. But if you make the distance between motor shaft and worm shaft very small, the hose can withstand forces from a shorter wormshaft.
There's only about 1/2" between the shafts. The two shafts almost line up with each other - there is only about a 5 degree angle between them.

Now I have to track down some tube. It looks like the smallest quantity I can buy is 20 ft, which would give me enough for 60 locomotives, if each locomotive needs 4".

Thanks Bob!

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Machine Shop / Locomotive Drive Work

Postby bob turner » Fri Nov 06, 2026 11:37 pm

https://www.yotashop.com/vacuum-hose-to ... gLLSvD_BwE

I think it is available in various lengths. This was the first that popped up. Another source has a very short length for $2.98 or something. Better if your shafts are closer than that - shoot for 1/8". You can do that with K&S tube, soldered or Loctited on the worm shaft.

Or this - half price:

https://www.ebay.com/itm/324713039404?_ ... R7ao-sS2aA

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Machine Shop / Locomotive Drive Work

Postby Rufus T. Firefly » Thu Nov 12, 2026 9:06 am

bob turner wrote:Or this - half price:

https://www.ebay.com/itm/324713039404?_ ... R7ao-sS2aA

A bit dear on the shipping - think shopping around more might be in order

US $19.99 Standard Shipping. See detailsfor shipping
Located in: Sharjah, United Arab Emirates
Due to US customs policies, the buyer of this item will need to pay import fees to the shipping carrier prior to delivery.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: Chris Webster and 49 guests