The Tridaily Doorstop -- Bob's Mexicano Electric

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby ScaleCraft » Sun May 29, 2022 5:58 pm

R.K. Maroon wrote:Dave, here is a similar unit, but one without roof-mounted air tanks. I would guess that the four objects in the middle of the roof are mufflers:

Image

This model is owned by Andy Brusgard, who was kind enough to send photos to me when I was first posting about doorstops on this forum.

Jim

yeah...this one has mufflers and exhaust at the end of same. Your first photo has air tanks. Could be mufflers, strange shape.

EDIT: Saved the photo, blew it up, compared. Both do have mufflers and those funny threaded pieces, the black one has air tanks, brown one does not.
I have had one or two of these before I started seriously into 2-rail 0. Gave it all to RK Hall.
Dave....gone by invitation

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby R.K. Maroon » Mon May 30, 2022 5:00 pm

Here is the underside of the Icken:

Image

The drive in this model looks quite a bit like the drive that Walthers developed around 1939-40 and used in their third version of their IR-GE oil-electric as well as in their doodlebug, MUs, and trolley models for many years thereafter. The tell for the Icken is the off-centerline location of the motor shaft. The shaft is offset because the motor is mounted 90 degrees from the on-centerline alignment used by everybody else in these vertical-motor drives, including the Walthers.

Another tell is the presence of the Icken stamp in the lead locomotive weight:

Image

Not many locomotives come from the factory with a custom (and somewhat crudely) poured lead weight, but I have seen these on several of the Icken boxcabs, so perhaps they were standard issue.
The link below any photo will display the image full size

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby bob turner » Mon May 30, 2022 9:57 pm

I have one like that. I was going to try to catch up on cabeese first - if I cut them in with edits I will so note in a new post. Mine is a Walthers Crestline, and came without rivets. Might be too late for a good photo - but you need to see this beauty. Four Escap motors driving four NWSL gearboxes.

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby bob turner » Mon May 30, 2022 10:14 pm

Yep, too late. fortunately I have some photos stored. Rivets are mine; mechanisms are George Wilson (RIP) of Lobaugh fame.
Side view:

Image

Bottom view:

Image

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby bob turner » Mon May 30, 2022 10:14 pm

Wanna do more Icken?

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby R.K. Maroon » Tue May 31, 2022 12:55 pm

More Ickens is always good. I will start a new heading for the PRR O1 tomorrow, but first a couple of last things regarding CN 7750. First, here is a photo of the prototype:

Image

I snagged this photo from the internet many years ago and failed to record an attribution. Here is another photo of the model for easy comparison:

Image

The model is representative but not a dead-nuts match. It should be noted that the CN version was not built by GE (like its US cousins) but instead was built by CN using Canada-sourced components wherever possible (CN was the national railroad, after all). Given the many variants of the oil-electrics in the US, it is somewhat surprising (and in this case fortunate) that the CN version is as close to the baseline US model is it is. Note 7750's service life came to a premature end when it was involved in a crash with an NW2 in the Mt Royal tunnel sometime after the war.

Finally, here is the oil-electric as listed in an Icken catalog flyer, circa 1940:

Image

Again, Andy Brusgard was kind enough to send a photo of one lettered per the catalog:

Image

If you look closely, the model is hand-lettered and sports the Icken mark under the road number at left. Very nice, Andy!
The link below any photo will display the image full size

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: The Tridaily Doorstop #26 -- Icken CN GE-IR Oil-Electric

Postby ScaleCraft » Tue May 31, 2022 1:50 pm

R.K. Maroon wrote:More Ickens is always good. I will start a new heading for the PRR O1 tomorrow, but first a couple of last things regarding CN 7750. First, here is a photo of the prototype:

Image

I snagged this photo from the internet many years ago and failed to record an attribution. Here is another photo of the model for easy comparison:

Image

The model is representative but not a dead-nuts match. It should be noted that the CN version was not built by GE (like its US cousins) but instead was built by CN using Canada-sourced components wherever possible (CN was the national railroad, after all). Given the many variants of the oil-electrics in the US, it is somewhat surprising (and in this case fortunate) that the CN version is as close to the baseline US model is it is. Note 7750's service life came to a premature end when it was involved in a crash with an NW2 in the Mt Royal tunnel sometime after the war.

Finally, here is the oil-electric as listed in an Icken catalog flyer, circa 1940:

Image

Again, Andy Brusgard was kind enough to send a photo of one lettered per the catalog:

Image

If you look closely, the model is hand-lettered and sports the Icken mark under the road number at left. Very nice, Andy!


Yeah, handrails around the roof and it would have been REAL close. That bottom photo...no stacks or mufflers...but third rail shoes along the bottom of the sideframes?
Dave....gone by invitation

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby R.K. Maroon » Wed Jun 01, 2022 1:14 pm

#27 -- Icken PRR O-1 Electric

Bob expressed an interest in posting more Ickens. He has one in particular that I don't have, and that is the Pennsylvania Railroad O-1 electric. As such, I decided to showcase that model with its own listing here. I trust that Bob will post photos of his model, but here are some photos from a flyer to get things started:

Image

Image
The link below any photo will display the image full size

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby bob turner » Wed Jun 01, 2022 2:29 pm

Indeed. I have one, and since the PRR almost always operated them in pairs, wish I had another. Castings were French sand, and exquisite. Mine is powered by two DC-91 motors, and last time I ran it it ran like the wind! Zoom!

You have seen these before (you have pretty much seen all of my significant models before):

Image

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby bob turner » Wed Jun 01, 2022 2:31 pm

Don't forget this one - also rumored to be Icken, although I usually think of it as an Alexander. I have two - one is powered with a Pittman can driving four CLW plastic gearboxes, the other is a dummy. We think they came from Watty House's collection in New England.

Image

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby bob turner » Wed Jun 01, 2022 2:34 pm

And I have three trucks ready with 40" wheelsets (should be 45") and am only days away from punching rivets for the NdeM 1001. I may need to beg Bob Stevenson for some radiator grille castings. The intervening days will be spent putting a firebox in a PRR G5. Just blocked out the frame and mounted drivers - and of course now that I have done that, a Saginaw G5 frame will surely appear.

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby R.K. Maroon » Thu Jun 02, 2022 7:00 pm

I hadn't noticed this before, but as best I can tell, the O-1, which did get its own flyer, does not appear in any regular Icken catalog (and I have a few). The flyer is undated, so it's not clear when this model first appeared. However, this ad for the model appeared in the March 1949 Model Railroader:

Image

Even with the flyer and the magazine ad, these models are quite rare. Perhaps the 1949 date explains it, as that is near the end of his "building new models" days. The price was quite high too, so that no doubt had something to do with it. Still, to invest in the patterns to make this fine cast model and not have a good number of them out there is a shame.
The link below any photo will display the image full size

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby bob turner » Fri Jun 03, 2022 2:44 pm

Check out Carey's excellent photos over on OGR. His even has the correct 45" wheelsets.

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby bob turner » Fri Jun 03, 2022 3:12 pm

This may take a minute - with Carey's permission (his password is not working):

Image

Image

Image

bob turner
Posts: 13675
Joined: Sat Jan 13, 2007 7:57 pm

Re: The Tridaily Doorstop #27 -- Icken PRR O-1 Electric

Postby bob turner » Fri Jun 03, 2022 3:14 pm

Somehow, Carey's photos are always more interesting than mine. Look at those background models!


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: up148 and 40 guests