The Tridaily Doorstop -- Bob's Mexicano Electric
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Tridaily Doorstop -- #2 Lobaugh UP Auto Car
I have a black UP auto car - I shall look to see if there are vestiges of Lobaugh.
I recall that you sent the Alexander gon. I have a Mini Scale box from your collection, and an aluminum auto car from Carey - neither is finished, but both are worthy. I shall post the Carswell gons in a minute. Carwell?
I recall that you sent the Alexander gon. I have a Mini Scale box from your collection, and an aluminum auto car from Carey - neither is finished, but both are worthy. I shall post the Carswell gons in a minute. Carwell?
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: The Tridaily Doorstop -- #2 Lobaugh UP Auto Car
Caswell, I believe
The link below any photo will display the image full size
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
#3 -- Alexander L&N Boxcar
Alexander produced several cast freight cars before the war. Here is one nicely hand-lettered for the L&N:


This one is definitely a doorstop, but not without some interest. Note the "Amraco" mark on the lower part of the car side to the left of the door:

"Amraco" was the short-hand for American Model Railroad Company, which is the formal name for Alexander's company. It's presence indicates that this is a factory-built model. Also note the extensive lettering on the right-hand side of the car, which can be seen in the first two photos. You would think they would have picked a different prototype, so as to avoid all that work!
Jim
Alexander produced several cast freight cars before the war. Here is one nicely hand-lettered for the L&N:
This one is definitely a doorstop, but not without some interest. Note the "Amraco" mark on the lower part of the car side to the left of the door:
"Amraco" was the short-hand for American Model Railroad Company, which is the formal name for Alexander's company. It's presence indicates that this is a factory-built model. Also note the extensive lettering on the right-hand side of the car, which can be seen in the first two photos. You would think they would have picked a different prototype, so as to avoid all that work!
Jim
The link below any photo will display the image full size
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
Here is the underside of the Alexander L&N boxcar:

This basic all-cast floor and frame is an easy tell for the various "house cars" offered by Alexander.
The trucks here may look like Lobaughs, but they are original Alexanders. The stamped brass bolster has a slightly different shape. I will see if I have a photo of just the truck somewhere in the files.

This basic all-cast floor and frame is an easy tell for the various "house cars" offered by Alexander.
The trucks here may look like Lobaughs, but they are original Alexanders. The stamped brass bolster has a slightly different shape. I will see if I have a photo of just the truck somewhere in the files.
The link below any photo will display the image full size
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
More an aside, I'm glad to see your models coming out of the boxes after the construction you showed us; I'm assuming the new building is complete?
-
Dennis Holler
- Posts: 474
- Joined: Mon Dec 13, 2010 8:31 pm
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
Oh I am curious about those Alexander trucks, I assume those are a later version? I was thinking the earlier ones were bronze cast sideframes and a simple U shaped Bronze cast center section? Are the side frame the same for both? Might cause me to realize I have some of that style Alexander truck tossed in my Lobaugh truck box lmao. I have a 40 ft auto boxcar that I am thinking is either Alexander or Scale Models, but it not does have that same distinctive Alexander base, same screww locations etc. It is interesting though as it has aluminum sides and ends and floor but a wood roof section. It has 2-39 stamped in the center sill much like one of my Alexander hopper cars has 12-37 stampped in the same area. I assume he was stamping the month/ year of that cars mfr... is that a good assumption?
Here are some pics of it. I should take it apart and see if there are any clues inside....




Here are some pics of it. I should take it apart and see if there are any clues inside....




Doorstop Rookie
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
Caswell. I think I have a pair of them. Auel trucks, which is the way they came to me. ATSF used them on Raton Pass. No idea who cast these:

I looked at my outside braced auto cars - none are Lobaugh.
I looked at my outside braced auto cars - none are Lobaugh.
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
Dennis -- I have a 40-ft single door boxcar with the same features. It has the early all-cast-bronze trucks associated with Alexander (and early Scale-Craft too). It is not date stamped, but on the floor inside the car is says either "BJ PA-X31" (or maybe "PJ PA-X31"). I assume that latter half of that means it is a model of a Pennsylvania X-31. I don't know what the BJ or PJ stands for, but I would assume the builder (or pattern maker -- it's part of the casting, not stamped later). I will take photos and put it in the queue to post.
Bob, Alexander offered a cast aluminum Caswell gondola. I recall that I have seen a catalog listing of this model, but I don't have it in hand so I can't be sure. As it is, it also appears in this photo that ran in the RMC "Collector Consist" column, May 1984. The Caswell is under the "A" in "American":

Yea, it would be nice if it were a better photo, but the gussets at the lower corners are unmistakable.
And finally, here is the L&N boxcar as it appears in the 1937 Alexander catalog:

The road number is the same as mine but the lettering scheme on the right side is a bit different, so not the exact same car.
Jim
Bob, Alexander offered a cast aluminum Caswell gondola. I recall that I have seen a catalog listing of this model, but I don't have it in hand so I can't be sure. As it is, it also appears in this photo that ran in the RMC "Collector Consist" column, May 1984. The Caswell is under the "A" in "American":

Yea, it would be nice if it were a better photo, but the gussets at the lower corners are unmistakable.
And finally, here is the L&N boxcar as it appears in the 1937 Alexander catalog:

The road number is the same as mine but the lettering scheme on the right side is a bit different, so not the exact same car.
Jim
The link below any photo will display the image full size
-
J. S. Bach
- Posts: 5820
- Joined: Wed May 16, 2007 9:30 pm
Re: The Tridaily Doorstop -- #3 Alexander L&N Boxcar
R.K. Maroon wrote: ...snip... And finally, here is the L&N boxcar as it appears in the 1937 Alexander catalog: ...snip... Jim
That finished car would be $242.02 in today's money; quite expensive back then!
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: The Tridaily Doorstop -- #4 Walthers PRR Automobile Box Car
# 4 -- Walthers PRR Automobile Box Car
Recall that I am posting these in the same order as the original "Doorstop of the Week" series, which was the better part of a decade ago. This was not long after I entered the hobby, and at that time my standards were a bit, shall we say, "unformed". I say that because this car "as is" was acceptable as a roster item at the time but does not cut it now:


I had either not heard of dull-coat or, more likely, was hesitant about any kind of spray paint (I have never been much of a painter). As it is, I am shooting some dull-coat in the paint booth this week, so I will dig out this model and see if I can do anything with it.
There is one thing worth noting here. The heavy coat of sealing varnish -- or fingernail polish, or whatever it is -- did perform its job of protecting the decal. This is a pre-war model, and it is rare to find decaled models, especially decals on wood, with the decals this well preserved.
Recall that I am posting these in the same order as the original "Doorstop of the Week" series, which was the better part of a decade ago. This was not long after I entered the hobby, and at that time my standards were a bit, shall we say, "unformed". I say that because this car "as is" was acceptable as a roster item at the time but does not cut it now:
I had either not heard of dull-coat or, more likely, was hesitant about any kind of spray paint (I have never been much of a painter). As it is, I am shooting some dull-coat in the paint booth this week, so I will dig out this model and see if I can do anything with it.
There is one thing worth noting here. The heavy coat of sealing varnish -- or fingernail polish, or whatever it is -- did perform its job of protecting the decal. This is a pre-war model, and it is rare to find decaled models, especially decals on wood, with the decals this well preserved.
The link below any photo will display the image full size
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: The Tridaily Doorstop -- #4 Walthers PRR Automobile Box Car
Suggestion: two coats of Future Floor Wax, applied with a Q-Tip in one direction only, dry for two days between coats, then Dullcote.
-
Dennis Holler
- Posts: 474
- Joined: Mon Dec 13, 2010 8:31 pm
Re: The Tridaily Doorstop -- #4 Walthers PRR Automobile Box Car
I've also got a few of those Walthers Boxcars, a couple of em in Blue Crestline boxes. All of em need some serious refurbishment though, but worth saving, although I find myself also realizing that some of the cars I bought long ago are not as acceptable now as before, same as you lol.
Doorstop Rookie
Re: The Tridaily Doorstop -- #4 Walthers PRR Automobile Box Car
Two things.
First; Why do you refer to it as a PRR automobile box? Looks a plain ol' X29 to my old eyes.
Second; Bob's technique using Future actually squares well with how I was (re)taught to decal models by the guy who painted the Oriental Limited "factory" paint. He was the guy who taught me to be able to consistently turn out tight decalling with no silvering. He was very dismissive of the common wisdom of using Dullcote or similar flat finishes over raw decals, pointing out it just made any blemishes far more obvious. He's right, too.
Decals are print over a gloss clear substrate, lacquer originally. After they are applied, common sense (rather than a hidebound adherence to "Kalmbachery") says blend them with gloss. The edges seal as do the prick-holes you made to get solvent under the decal to get rid of any air-pockets and silvering. The finish blends. Here is why Bob's technique using Future works.
Then, you can weather or dull to suit and your decals remain tight as they are actually part of the finished surface, one that has an even sheen throughout.
First; Why do you refer to it as a PRR automobile box? Looks a plain ol' X29 to my old eyes.
Second; Bob's technique using Future actually squares well with how I was (re)taught to decal models by the guy who painted the Oriental Limited "factory" paint. He was the guy who taught me to be able to consistently turn out tight decalling with no silvering. He was very dismissive of the common wisdom of using Dullcote or similar flat finishes over raw decals, pointing out it just made any blemishes far more obvious. He's right, too.
Decals are print over a gloss clear substrate, lacquer originally. After they are applied, common sense (rather than a hidebound adherence to "Kalmbachery") says blend them with gloss. The edges seal as do the prick-holes you made to get solvent under the decal to get rid of any air-pockets and silvering. The finish blends. Here is why Bob's technique using Future works.
Then, you can weather or dull to suit and your decals remain tight as they are actually part of the finished surface, one that has an even sheen throughout.
- Rufus T. Firefly
- Posts: 42229
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: The Tridaily Doorstop -- #4 Walthers PRR Automobile Box Car
.
Last edited by Rufus T. Firefly on Tue Apr 26, 2022 5:07 pm, edited 1 time in total.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: The Tridaily Doorstop -- #4 Walthers PRR Box Car
sarge wrote:Why do you refer to it as a PRR automobile box? Looks a plain ol' X29 to my old eyes
Yes, thanks for pointing that out. It was a cut-and-paste error.
bob turner wrote:Suggestion: two coats of Future Floor Wax, then Dullcote.
Ah! Thanks, Bob. I have a bottle of this but use it so infrequently that I forget I have it:

The first coat went on today. I will post photos once the process is complete.
sarge wrote:Common sense says to blend decals with gloss
Agreed. I have relatively little experience with paint and decals, but Brother Pete recommended topcoating decals with gloss to better hide the edges, and then dull coat as you wish. I have tried this once with very satisfactory results. Highly recommended.
Now back to the car at hand. Dennis mentioned "Blue Box" Crestline cars. The PRR boxcar fits the bill:


These are the earliest Walthers cars that I know of -- that is, if Walthers shipped then in a different box before this one, it is undiscovered by me. Note that this boxcar was sold as a two-rail model. I don't have production numbers, but it seems that most models from that era were sold with uninsulated wheels, either for center third rail or outside third rail operation.
Jim
The link below any photo will display the image full size
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 47 guests