LWS/ Penn-Erie U50 in pewter
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Soldering pewter?
I made the right choice. Very pleased with the results.
I note that I joined two Lionel die cast tender bodies in a butt joint - in 1966 - with dime store epoxy. Still together after more than a half century. I think JB Weld is an order of magnitude better, for tenacity.
Next step - I am loathe to use the window screen supplied in the kit. I think expanded metal would look a lot better - but am unaware of sources. I think it should be "screen-like;" having square openings (rather than round ones). I am not above using plain old screen; just not window screen.
Also, did you note Maroon's U 50 window mullions? Not sure I am up to that level of detail, but I shall try.
Last question: Is it U50, U-50 or U 50? Just trying to be precise in an area where I am totally ignorant.
I note that I joined two Lionel die cast tender bodies in a butt joint - in 1966 - with dime store epoxy. Still together after more than a half century. I think JB Weld is an order of magnitude better, for tenacity.
Next step - I am loathe to use the window screen supplied in the kit. I think expanded metal would look a lot better - but am unaware of sources. I think it should be "screen-like;" having square openings (rather than round ones). I am not above using plain old screen; just not window screen.
Also, did you note Maroon's U 50 window mullions? Not sure I am up to that level of detail, but I shall try.
Last question: Is it U50, U-50 or U 50? Just trying to be precise in an area where I am totally ignorant.
Re: Soldering pewter?
Acording to "Diesel Locomotives:The First 50 Years", Louis Marre, Kalmbach, 1995 it is U50.
roger
I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH
I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH
Re: Soldering pewter?
bob turner wrote:Last question: Is it U50, U-50 or U 50? Just trying to be precise in an area where I am totally ignorant.
U50
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Soldering pewter?
Thanks. From now on that is what it will be.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Soldering pewter?
Drilled all but four handrail post and grab iron holes - always use cutting fluid when drilling pewter - and gave the body its first coat of primer.
I would never have guessed that pewter woulf be a decent material for a model locomotive, but I am about to change my mind. Might be a tad heavy, and might not survive being dropped, but this is one impressive model!
Most of the epoxied seams have disappeared. Side seams are at door impressions, so I may wind up scraping into the seam to re-create door edges. Maybe not. Still looking at it.
Perforated metal was what I was thinking of for the screens. A hundred bucks a foot! Back to window screen. Looks ok on Maroon's model.
I would never have guessed that pewter woulf be a decent material for a model locomotive, but I am about to change my mind. Might be a tad heavy, and might not survive being dropped, but this is one impressive model!
Most of the epoxied seams have disappeared. Side seams are at door impressions, so I may wind up scraping into the seam to re-create door edges. Maybe not. Still looking at it.
Perforated metal was what I was thinking of for the screens. A hundred bucks a foot! Back to window screen. Looks ok on Maroon's model.
Re: Soldering pewter?
The individual pieces of glass are "wrapped" by a metal "channel" that is soldered where the ends meet. I never did stained glass, but I suspect the difficult part is nipping the glass to the wanted shape.
Yes, you wrap each piece with foil and then assemble the pieces and float solder them together. I use a glass router to fine fit/shape the parts for minimal amounts of solder.
I believe you will have to fudge the drive train as the prototype uses a span bolster to bridge the B-B trucks.
Have you looked for/at brass screens from a supplier of O gauge two rail detail parts like P&D in Roseville, Michigan? Don't forget to look at 1/35 scale armor photo etch parts and possibly 1/350 or 1/144 scale ship parts.
BTW, it is looking great.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Soldering pewter?
Thanks Chuck. The model must also use a span bolster, but I am thinking steel bar narrow enough for Delrin chain to go around. The only hassle will be the tight space between tandem trucks for a U-joint. I think it is doable with chain All Nation drives.
Good idea on the ship/armor suppliers. I opted for window screen, and it looks ok. Thinking about water-based contact cement to attach them. Any ideas? First coat of yellow is on, so I cannot use acetone or MEK-based cements.
Good idea on the ship/armor suppliers. I opted for window screen, and it looks ok. Thinking about water-based contact cement to attach them. Any ideas? First coat of yellow is on, so I cannot use acetone or MEK-based cements.
Re: Soldering pewter?
Have you considered scratch building the radiator louvers out of sheet styrene or PlastStuct shapes?
Have you considered vertical can motors for the inner trucks and weighted dummies as the lead trucks? Sort of an articulated arrangement like the Williams GG-1 between the powered truck(s) and the two axle lead trucks.

Something this long and heavy will have issues with chain drive even with extremely large curves (O-110 +)
Have you considered vertical can motors for the inner trucks and weighted dummies as the lead trucks? Sort of an articulated arrangement like the Williams GG-1 between the powered truck(s) and the two axle lead trucks.

Something this long and heavy will have issues with chain drive even with extremely large curves (O-110 +)
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
- Rufus T. Firefly
- Posts: 42229
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Soldering pewter?
chuck wrote:Have you considered scratch building the radiator louvers out of sheet styrene or PlastStuct shapes?
Might be able to use N or HO scale clapboard? Also possible might be the louver decals from Archer.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Soldering pewter?
If I power it, it will be eight axles powered. I will do a "proof of concept" assembly next week - may look like an All Nation setup with tower on the fourth axle driving three axle gearboxes and a sliding U joint.
On the screen - the real thing uses screen, so screen it is. Window screen goes in tonight, before the second coat of yellow. I may at some point opt for slightly finer mesh screen.
On the screen - the real thing uses screen, so screen it is. Window screen goes in tonight, before the second coat of yellow. I may at some point opt for slightly finer mesh screen.
Re: Soldering pewter?
I think I got some small gauge brass mesh at P&D to make the fold down "steps" on the old Renwal Atomic Canon.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
Re: Soldering pewter?
Just noticed this thread and it's a very interesting project Bob. All baby turbines (4500 HP) and the U50 used span bolsters and I might have some photos of the type OMI used. I understand LW also offered a Veranda turbine, although I've never seen one.
"The U50 is sometimes inaccurately referred to as the U50D, a back-formation from the U50C name given to the six-axle units. The name is incorrect and was never used by the manufacturer or the railroad. The U50 did not ride on D trucks in any case. It is also sometimes referred to as the U50B, but this is incorrect as well."
Look forward to following your thread.
"The U50 is sometimes inaccurately referred to as the U50D, a back-formation from the U50C name given to the six-axle units. The name is incorrect and was never used by the manufacturer or the railroad. The U50 did not ride on D trucks in any case. It is also sometimes referred to as the U50B, but this is incorrect as well."
Look forward to following your thread.
- Rufus T. Firefly
- Posts: 42229
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Soldering pewter?
up148 wrote:I understand LW also offered a Veranda turbine, although I've never seen one.
Might have, but unless it was actually ordered it might not have been produced...
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Soldering pewter?
This huge unit was off my radar until I saw Maroon’s photo. I have since learned a few things - like Maroon’s U50 has nose grabirons on the left, and the ladder ahead of the first triangular support. #s31, 32, and 33 are like that, but37 and up are different.
Not that I want to be a rivet counter - but can you recommend a picture book that maybe features these and the turbines? Most of my current info is from Maroon’s photos and the Google.
Not that I want to be a rivet counter - but can you recommend a picture book that maybe features these and the turbines? Most of my current info is from Maroon’s photos and the Google.
- R.K. Maroon
- Posts: 3140
- Joined: Tue Feb 22, 2011 9:20 pm
Re: Soldering pewter?
Bob -- I have a copy of this soft-cover book:

Copies are available:
https://www.amazon.com/Union-Pacifics-Big-GEs-U50C/dp/B011G835NI
I damn sure didn't pay $150 for my copy. I can send you mine but I am not in Dallas at present.
Copies are available:
https://www.amazon.com/Union-Pacifics-Big-GEs-U50C/dp/B011G835NI
I damn sure didn't pay $150 for my copy. I can send you mine but I am not in Dallas at present.
The link below any photo will display the image full size
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: R.K. Maroon and 48 guests
