NWSL
-
Chris Webster
- Posts: 956
- Joined: Mon May 25, 2015 8:25 pm
Re: NWSL
They have an online parts store: Bachmann Trains Parts Department (but Jay probably already knew that.)Jay Criswell wrote:Not really familiar with anything Bachmann makes for O Scale (HO & On30, yes). Would it be possible to share more info on what's available through them?
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: NWSL
I have some experience with Botchman.
And parent Kader.
There is a reason they have a parts department.
They have recently decided to use brass worm and worm gears in some of their products.
Usually cast plastic gears pressed onto axles.
Crack.
And other than once glaring example, usually Mabuchi (cheap) cans.
I have too much experience there.....never again anything new from any Botchman line.
Turner.
And parent Kader.
There is a reason they have a parts department.
They have recently decided to use brass worm and worm gears in some of their products.
Usually cast plastic gears pressed onto axles.
Crack.
And other than once glaring example, usually Mabuchi (cheap) cans.
I have too much experience there.....never again anything new from any Botchman line.
Turner.
Dave....gone by invitation
Re: NWSL
My previous Bachmann reference, was to Williams by Bachmann. They also make large scale. Gears for the above should be appropriate for O scale, and available through Chris's Bachmann parts link, above.
Just a guess, but their On30 gears are probably made to the same diametral pitch/module as HO gears.
Just a guess, but their On30 gears are probably made to the same diametral pitch/module as HO gears.
Torturers, White Racists, Gay Bashers, Rich Psychopaths.
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: NWSL
Chris,
Yeah, I looked at it earlier today (first time) and found way too much stuff. To be honest, most of it looked like junk...kinda what I expected. I'm willing to try something but I'd like a little more guidance.
I prefer metal gearbox cases with an enclosed steel worm, separate bearings (ball preferred but bronze okay), bronze and Delrin (engineering plastic) worm gears and reverse worm gears).
My gear boxes use steel gears but they are turning very slowly with ball bearings throughout.
Jay
Yeah, I looked at it earlier today (first time) and found way too much stuff. To be honest, most of it looked like junk...kinda what I expected. I'm willing to try something but I'd like a little more guidance.
I prefer metal gearbox cases with an enclosed steel worm, separate bearings (ball preferred but bronze okay), bronze and Delrin (engineering plastic) worm gears and reverse worm gears).
My gear boxes use steel gears but they are turning very slowly with ball bearings throughout.
Jay
Re: NWSL
Jay Criswell wrote:My gear boxes use steel gears but they are turning very slowly with ball bearings throughout.
Are all the gears in your gear train steel? And, are you using thrust bearings on your helical gears?
Torturers, White Racists, Gay Bashers, Rich Psychopaths.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: NWSL
Dissimilar steel alloys can work.
I am with Jay on all the particulars - except I got excellent results with Raoul's glass-filled cases, and not bad results from the regular black plastic Mod 0.5 cases.
Sunset gear boxes are quite good now. They should offer them separately.
I am with Jay on all the particulars - except I got excellent results with Raoul's glass-filled cases, and not bad results from the regular black plastic Mod 0.5 cases.
Sunset gear boxes are quite good now. They should offer them separately.
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: NWSL
Roy,
There are thrust washers between the gears and ball bearings.
Jay
There are thrust washers between the gears and ball bearings.
Jay
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: NWSL
Bob,
Sure, the plastic NWSL boxes are okay, I have dozens. Just stating preferences. Like so many things these days, we take what we can get.
Jay
Sure, the plastic NWSL boxes are okay, I have dozens. Just stating preferences. Like so many things these days, we take what we can get.
Jay
-
Chris Webster
- Posts: 956
- Joined: Mon May 25, 2015 8:25 pm
Re: NWSL
There was a reason why NWSL made parts intended to replace Bachmann parts...Jay Criswell wrote:To be honest, most of it looked like junk...kinda what I expected.
Roy wrote:My previous Bachmann reference, was to Williams by Bachmann. They also make large scale. Gears for the above should be appropriate for O scale, and available through Chris's Bachmann parts link, above.
I've purchased several G-gauge parts from that store, but I cannot recommend them as a parts source for Jay.
Jay does fine precision mechanisms, while Bachmann does inexpensive and rugged (intended to be operated outside in the yard.) If you understand that, then Bachmann models can be awesome bargains -- heck, brand new Fn3 Climaxes, with factory-installed DCC and sound, are currently being sold on ebay for $235/each!
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: NWSL
Chris Webster wrote:I've purchased several G-gauge parts from that store, but I cannot recommend them as a parts source for Jay.
Jay does fine precision mechanisms, while Bachmann does inexpensive and rugged (intended to be operated outside in the yard.) If you understand that, then Bachmann models can be awesome bargains -- heck, brand new Fn3 Climaxes, with factory-installed DCC and sound, are currently being sold on ebay for $235/each!
I could tell you stories. Fortunately backed up by boxes and boxes of saved broken stuff.
Plastic gears...heck, I would get new outside-frames 2-8-0's in for conversion....inspection showed, brand new, hub of axle gear cracked. One night we lost two axle gears in 20 minutes.
Regrind plastic.
First run Shays that fell apart in the box or on the shelf. Split cases, cracked covers....and when they "fixed" the 8-screw trucks, they just hid the two long screws under the bottom plate....and whacked the end of the original screws with lineman pliers and jammed them in, burrs, distortion and all.
No double-lead worms....jerk along on downgrades.
Climax? Gimme a break...oh, wait...they break themselves. First run, each truck drove one end of their respective driveshafts via internal gearing. Driveshafts went to center gearbox....oh, wait...no slip joints anywhere. Usually stripped a gear or snapped the ears off the yoke on the end of the center gearbox.....fun to fix (and I have...quite a few).
What're they on, version six of the 4-6-0?
Wires...three freaking strands on some of it it seems. Oh, we bought 10,000 feet of red and folks complained? Next run it's black....until you work on it, and the black spray paint sloughs off in your hands.
Ever seen their idea of track pickups for lighting on their passenger cars?
I could go on. But I shall naught.
On board sockets...another layer of PRC electronics? I cut them out and start over.
Dave....gone by invitation
-
Chris Webster
- Posts: 956
- Joined: Mon May 25, 2015 8:25 pm
Re: NWSL
And I presume you fixed them using NWSL axle gear, one of the parts I as referring to...ScaleCraft wrote:Plastic gears...heck, I would get new outside-frames 2-8-0's in for conversion....inspection showed, brand new, hub of axle gear cracked. One night we lost two axle gears in 20 minutes.
Last edited by Chris Webster on Tue Jul 09, 2019 6:22 am, edited 1 time in total.
-
bob turner
- Posts: 13676
- Joined: Sat Jan 13, 2007 7:57 pm
Re: NWSL
Probably. Weaver had the same problem. Raoul aged his plastic stock before boring and hobbing. I have never seen an NWSL gear fail from shrinkage. We went through three motors on one Mod 0.5 gearbox. That's running 8 hours a day.
- ScaleCraft
- Posts: 6693
- Joined: Thu Jan 26, 2012 10:15 pm
Re: NWSL
[/quote]Chris Webster wrote:And I presume you fixed them using NWSL axle gear, one of the parts I as referring to...ScaleCraft wrote:Plastic gears...heck, I would get new outside-frames 2-8-0's in for conversion....inspection showed, brand new, hub of axle gear cracked. One night we lost two axle gears in 20 minutes.![]()
Wherever possible, a Barry's chassis or gearbox.
Dave....gone by invitation
Re: NWSL
Athearn was a bit adventurous, with some of his drive designs. I seem to recall seeing plastic herringbone gears, in something of his. If he had only gone to a two-stage reduction, on his rubber band drive! In addition to being inexpensive, quiet and fairly easy to repair, it could've given good slow speed operation. Especially, with the flywheels he put on his later production motors.
Torturers, White Racists, Gay Bashers, Rich Psychopaths.
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 49 guests