2Railing An Weaver VO-1000 Doable?

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Thu Jun 13, 2019 11:02 am

Hang on! :D
Image
Last edited by 2railjon on Thu Jun 13, 2019 11:20 am, edited 2 times in total.
Running that red block Charlie.

Jay Criswell
Posts: 2004
Joined: Thu Mar 06, 2008 12:38 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby Jay Criswell » Thu Jun 13, 2019 11:06 am

Oh yeah, and another other thing, don't fall into the trap of thinking the wipers have to contact the back of the wheel. The face of the wheel, hidden from view, should be much easier, in the case.

Okay, I'm done...for now.

Jay

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: 2Railing An Weaver VO-1000 Doable?

Postby Rufus T. Firefly » Thu Jun 13, 2019 12:40 pm

Jay Criswell wrote:..........drill & tap prior to attachment.


Words to print and frame over the work bench, :mrgreen:
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby bob turner » Thu Jun 13, 2019 2:34 pm

Don't know if this would work for you, but on two of my models I hung the bracket between the wheel tread, attached to the side frame but insulated, with spring-loaded brass plungers hitting the wheel tread. These are my smoothest running Diesels.

Also, in desperation I put track sliders on an All Nation sintered iron NW. It, too, is quite smooth. You only see them when you make the effort to scrutinize.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Thu Jun 13, 2019 4:09 pm

Alright! I was already kind of in step with Sarge’s design except I took the poor mans route! Not having any circuit boards I used a couple of Atlas coupler covers as insulation. Then wipers from an MTH Passenger truck held in place by drilled & tapped 4-40 nylon screws.
Image
Runs like a champ thanks to Jays awesome work!!
I’m only putting wipers on one side of the trucks as I have no turnouts and all my Rail joints are soldered.
Image

Tomorrow lighting and couplers! :shock:
Running that red block Charlie.

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: 2Railing An Weaver VO-1000 Doable?

Postby Rufus T. Firefly » Thu Jun 13, 2019 4:14 pm

2railjon wrote:..........I used a couple of Atlas coupler covers as insulation.


Best use yet of Atlas couplers! :mrgreen:
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

Jay Criswell
Posts: 2004
Joined: Thu Mar 06, 2008 12:38 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby Jay Criswell » Thu Jun 13, 2019 4:35 pm

Cool! But does it run?

Jay

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Thu Jun 13, 2019 6:44 pm

Jay Criswell wrote:Cool! But does it run?

Jay


Absolutely,Jay! You saved the VO a trip to the dump!
Link:
https://youtu.be/2sUca68ooQo
Running that red block Charlie.

Jay Criswell
Posts: 2004
Joined: Thu Mar 06, 2008 12:38 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby Jay Criswell » Thu Jun 13, 2019 7:03 pm

So, now it's my fault!

Jay

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Thu Jun 13, 2019 7:47 pm

Jay, from fried boards sitting in the attic 10 years to back on the rails again is great! :D
Running that red block Charlie.

User avatar
De Bruin
Posts: 992
Joined: Thu Jan 12, 2017 8:24 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby De Bruin » Thu Jun 13, 2019 11:37 pm

Having a weakness for Weaver's and also thinking this VO is one of his better latter efforts car-body wise; you have to like a model that offers you two different exhaust stack options depending on your prototype. The CB&Q's VO's were outliers on that road for decades that's for sure, and looked great in that scheme too boot. Seen quite a few photos of them switching CUS.

I've enjoyed reading this. Jon's experience with the solidified concrete-like factory grease is consistent with two of these I've had the adventure to make run, and note they were both factory 2-rail, like the china-drive FA both also suffered from fly-wheel-itis wherein the fly-wheels were not pressed on deep enough to clear the inside of the car-body. What a pain in the butt. And the original harness wiring? Yikes what a kluge.
Also note the VO's two rail factory leaf wiper is shorter than the standard found on the FA-RS3-RS11,RSC12-GP38 series.
Fun - not.
Regardless,
Great model, and very cool,informative thread, thanks.
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Fri Jun 14, 2019 9:35 am

Thanks for chiming in, De Bruin!
I see I do have a packet of taller smoke stacks in the box. I wish Jim Weaver was still in business as I’ll bet I could have got a couple 2Rail coupler mounting brackets from him! This looks like it’s going to be a headache! :mrgreen:
Image
Running that red block Charlie.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Fri Jun 14, 2019 12:41 pm

Here are some detail shots of a Weaver 2Rail VO coupler area. Looks like a need to pick up some styrene sheets! :mrgreen:
Image

Image
Image
Running that red block Charlie.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby 2railjon » Fri Jun 14, 2019 2:30 pm

While I ponder the couplings I’ve got the lighting figured out.
Image

Image

Don’t make fun of my playschool transformer. I’m not poor, I’m cheap! :lol:
Running that red block Charlie.

User avatar
ScaleCraft
Posts: 6693
Joined: Thu Jan 26, 2012 10:15 pm

Re: 2Railing An Weaver VO-1000 Doable?

Postby ScaleCraft » Fri Jun 14, 2019 9:19 pm

Wouldn't dream of making fun of you plaiskewl transformer. Lights in the cab, maybe, but not the transformer.
Dave....gone by invitation


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: Google [Bot] and 45 guests