LWS/ Penn-Erie U50 in pewter

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Soldering pewter?

Postby bob turner » Sat May 29, 2021 2:21 pm

I made the right choice. Very pleased with the results.

I note that I joined two Lionel die cast tender bodies in a butt joint - in 1966 - with dime store epoxy. Still together after more than a half century. I think JB Weld is an order of magnitude better, for tenacity.

Next step - I am loathe to use the window screen supplied in the kit. I think expanded metal would look a lot better - but am unaware of sources. I think it should be "screen-like;" having square openings (rather than round ones). I am not above using plain old screen; just not window screen.

Also, did you note Maroon's U 50 window mullions? Not sure I am up to that level of detail, but I shall try.

Last question: Is it U50, U-50 or U 50? Just trying to be precise in an area where I am totally ignorant.

User avatar
rogruth
Posts: 24452
Joined: Sun Aug 14, 2005 8:32 pm
Location: pembroke,ga

Re: Soldering pewter?

Postby rogruth » Sat May 29, 2021 10:29 pm

Acording to "Diesel Locomotives:The First 50 Years", Louis Marre, Kalmbach, 1995 it is U50.
roger

I support thread drift.
If God didn't want women to be looked at, He would have made 'em ugly. RAH

E7
Posts: 8404
Joined: Wed Dec 12, 2007 1:35 am

Re: Soldering pewter?

Postby E7 » Sat May 29, 2021 10:46 pm

bob turner wrote:Last question: Is it U50, U-50 or U 50? Just trying to be precise in an area where I am totally ignorant.


U50

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Soldering pewter?

Postby bob turner » Sat May 29, 2021 11:43 pm

Thanks. From now on that is what it will be.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Soldering pewter?

Postby bob turner » Mon May 31, 2021 10:47 pm

Drilled all but four handrail post and grab iron holes - always use cutting fluid when drilling pewter - and gave the body its first coat of primer.
I would never have guessed that pewter woulf be a decent material for a model locomotive, but I am about to change my mind. Might be a tad heavy, and might not survive being dropped, but this is one impressive model!
Most of the epoxied seams have disappeared. Side seams are at door impressions, so I may wind up scraping into the seam to re-create door edges. Maybe not. Still looking at it.

Perforated metal was what I was thinking of for the screens. A hundred bucks a foot! Back to window screen. Looks ok on Maroon's model.

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: Soldering pewter?

Postby chuck » Tue Jun 01, 2021 8:30 pm

The individual pieces of glass are "wrapped" by a metal "channel" that is soldered where the ends meet. I never did stained glass, but I suspect the difficult part is nipping the glass to the wanted shape.


Yes, you wrap each piece with foil and then assemble the pieces and float solder them together. I use a glass router to fine fit/shape the parts for minimal amounts of solder.

I believe you will have to fudge the drive train as the prototype uses a span bolster to bridge the B-B trucks.

Have you looked for/at brass screens from a supplier of O gauge two rail detail parts like P&D in Roseville, Michigan? Don't forget to look at 1/35 scale armor photo etch parts and possibly 1/350 or 1/144 scale ship parts.

BTW, it is looking great.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Soldering pewter?

Postby bob turner » Tue Jun 01, 2021 11:14 pm

Thanks Chuck. The model must also use a span bolster, but I am thinking steel bar narrow enough for Delrin chain to go around. The only hassle will be the tight space between tandem trucks for a U-joint. I think it is doable with chain All Nation drives.

Good idea on the ship/armor suppliers. I opted for window screen, and it looks ok. Thinking about water-based contact cement to attach them. Any ideas? First coat of yellow is on, so I cannot use acetone or MEK-based cements.

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: Soldering pewter?

Postby chuck » Wed Jun 02, 2021 10:42 am

Have you considered scratch building the radiator louvers out of sheet styrene or PlastStuct shapes?

Have you considered vertical can motors for the inner trucks and weighted dummies as the lead trucks? Sort of an articulated arrangement like the Williams GG-1 between the powered truck(s) and the two axle lead trucks.

Image

Something this long and heavy will have issues with chain drive even with extremely large curves (O-110 +)
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Soldering pewter?

Postby Rufus T. Firefly » Wed Jun 02, 2021 12:12 pm

chuck wrote:Have you considered scratch building the radiator louvers out of sheet styrene or PlastStuct shapes?


Might be able to use N or HO scale clapboard? Also possible might be the louver decals from Archer.
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Soldering pewter?

Postby bob turner » Wed Jun 02, 2021 1:40 pm

If I power it, it will be eight axles powered. I will do a "proof of concept" assembly next week - may look like an All Nation setup with tower on the fourth axle driving three axle gearboxes and a sliding U joint.

On the screen - the real thing uses screen, so screen it is. Window screen goes in tonight, before the second coat of yellow. I may at some point opt for slightly finer mesh screen.

User avatar
chuck
Posts: 5867
Joined: Thu May 27, 2004 8:43 pm
Location: Plymouth, Michigan
Contact:

Re: Soldering pewter?

Postby chuck » Wed Jun 02, 2021 2:07 pm

I think I got some small gauge brass mesh at P&D to make the fold down "steps" on the old Renwal Atomic Canon.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?

up148
Posts: 4796
Joined: Sat Nov 01, 2008 11:52 am

Re: Soldering pewter?

Postby up148 » Wed Jun 02, 2021 3:47 pm

Just noticed this thread and it's a very interesting project Bob. All baby turbines (4500 HP) and the U50 used span bolsters and I might have some photos of the type OMI used. I understand LW also offered a Veranda turbine, although I've never seen one.

"The U50 is sometimes inaccurately referred to as the U50D, a back-formation from the U50C name given to the six-axle units. The name is incorrect and was never used by the manufacturer or the railroad. The U50 did not ride on D trucks in any case. It is also sometimes referred to as the U50B, but this is incorrect as well."

Look forward to following your thread.

User avatar
Rufus T. Firefly
Posts: 42229
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Soldering pewter?

Postby Rufus T. Firefly » Wed Jun 02, 2021 5:24 pm

up148 wrote:I understand LW also offered a Veranda turbine, although I've never seen one.


Might have, but unless it was actually ordered it might not have been produced...
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Soldering pewter?

Postby bob turner » Wed Jun 02, 2021 9:18 pm

This huge unit was off my radar until I saw Maroon’s photo. I have since learned a few things - like Maroon’s U50 has nose grabirons on the left, and the ladder ahead of the first triangular support. #s31, 32, and 33 are like that, but37 and up are different.

Not that I want to be a rivet counter - but can you recommend a picture book that maybe features these and the turbines? Most of my current info is from Maroon’s photos and the Google.

User avatar
R.K. Maroon
Posts: 3140
Joined: Tue Feb 22, 2011 9:20 pm

Re: Soldering pewter?

Postby R.K. Maroon » Wed Jun 02, 2021 10:40 pm

Bob -- I have a copy of this soft-cover book:

Image

Copies are available:

https://www.amazon.com/Union-Pacifics-Big-GEs-U50C/dp/B011G835NI

I damn sure didn't pay $150 for my copy. I can send you mine but I am not in Dallas at present.
The link below any photo will display the image full size


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 55 guests