.

Discuss All Facets of 2-Rail, 1/48 Scale, Model Railroading
User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

.

Postby 2railjon » Tue Jan 23, 2018 10:20 am

.
Last edited by 2railjon on Sun May 27, 2018 5:29 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
Rufus T. Firefly
Posts: 42227
Joined: Wed May 16, 2007 7:52 am
Location: To be Determined

Re: Help With 3 Rail Locomotive Conversion

Postby Rufus T. Firefly » Tue Jan 23, 2018 10:47 am

2railjon wrote:Can anyone share who does 3 Rail locomotive to 2 Rail conversions? It a Weaver 4-4-2 and I have a complete wheel, driver, tender set in 2 Rail from Sunset if that will aid in conversion.
Thanks!


Joe F. who posts here does conversions but those usually entail the creation of drivers. If you can just swap out the drivers, that's the only bit that's got some challenge to it. Rest should be pretty straightforward.

Which 4-4-2?
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.

User avatar
sarge
Posts: 5138
Joined: Thu Apr 02, 2009 2:21 pm
Location: Dungfield Manor

Re: Help With 3 Rail Locomotive Conversion

Postby sarge » Tue Jan 23, 2018 12:03 pm

Weaver model with Sunset parts? Might be a bit more problematic than a screwdriver job.

PM Joe and see what he says.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Tue Jan 23, 2018 12:50 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:30 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Tue Jan 23, 2018 1:26 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:30 pm, edited 1 time in total.
Running that red block Charlie.

bob turner
Posts: 13676
Joined: Sat Jan 13, 2007 7:57 pm

Re: Help With 3 Rail Locomotive Conversion

Postby bob turner » Tue Jan 23, 2018 1:47 pm

Before getting carried away, disassemble the two, and attempt a trial fit. Weaver and Sunset may be thousands of miles apart, but their Korean builder probably sleeps with himself.

Do you have two complete models, or just the mechanism for the 2-rail?

Robert
Posts: 1051
Joined: Sat Dec 11, 2010 3:00 pm

Re: Help With 3 Rail Locomotive Conversion

Postby Robert » Tue Jan 23, 2018 1:58 pm

2railjon wrote:Anyone have Joes user name here?
I’m not finding it. Thanks!


Here you go Jon.

rrjjf

Robert

rrjjf
Posts: 593
Joined: Tue May 08, 2007 5:13 am
Location: Glen Arm Maryland

Re: Help With 3 Rail Locomotive Conversion

Postby rrjjf » Tue Jan 23, 2018 3:28 pm

With regard to using different drivers to convert a 3 rail model to 2 rail operation you will probably have some problems with the crankpins and rods. Most 3 rail "scale" steam model incorporate an odd hollow eccentric crankpin that a metric screws goes through into the driver's crankpin along with some spacers and sleeves. IMO, much easier with a lathe to convert the 3 rail drivers that are made to use with the model's rods to a scale profile.

Joe
Joe Foehrkolb

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Tue Jan 23, 2018 6:25 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:30 pm, edited 1 time in total.
Running that red block Charlie.

rrjjf
Posts: 593
Joined: Tue May 08, 2007 5:13 am
Location: Glen Arm Maryland

Re: Help With 3 Rail Locomotive Conversion

Postby rrjjf » Wed Jan 24, 2018 6:21 pm

2RailJohn

I tried reaching you on the phone number you sent to me and got a mechanical message that the phone was not in service.

Joe
Joe Foehrkolb

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Wed Jan 24, 2018 6:30 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:31 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Wed Jan 24, 2018 6:39 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:31 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
rex desilets
Posts: 1786
Joined: Sun Jul 15, 2007 2:18 pm

Re: Help With 3 Rail Locomotive Conversion

Postby rex desilets » Wed Jan 24, 2018 6:45 pm

Lovely, lovely cars. Are they scale length?
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” – John Adams

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Wed Jan 24, 2018 7:04 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:32 pm, edited 1 time in total.
Running that red block Charlie.

User avatar
2railjon
Posts: 15906
Joined: Fri Apr 02, 2004 2:33 pm

Re: Help With 3 Rail Locomotive Conversion

Postby 2railjon » Wed Jan 24, 2018 7:21 pm

.
Last edited by 2railjon on Sun May 27, 2018 5:32 pm, edited 1 time in total.
Running that red block Charlie.


Return to “O-Gauge, 2-Rail, Model Railroading”

Who is online

Users browsing this forum: No registered users and 28 guests