Page 1 of 1
Need GM or A-N NW2 part
Posted: Fri Jul 10, 2020 4:21 pm
by ScaleCraft
For three rail versions, there was this multiple bend piece that fit around the non-powered truck axles, ridged, to hold pickup assembly. Anybody converting one of these to 2-rail will remove them!
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 2:33 pm
by ScaleCraft
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 2:42 pm
by bob turner
Most of us pitch this sort of stuff. Try the 3-Rail forums?
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 2:49 pm
by ScaleCraft
Did both. I would imagine usually the 2-rail folks have them from conversions to 2-rail. This is for the next one, a dummy, got a power truck (vertical motor, field wound) waiting to hear back on getting wheels changed out.
No rush, thought I'd start early looking.
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 6:52 pm
by Rufus T. Firefly
ScaleCraft wrote:I would imagine usually the 2-rail folks have them from conversions to 2-rail.
There's so many 2 rail ones available that converting them isn't worth the time.
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 7:00 pm
by DaveJfr0
Don't have, but can you measure the thickness and roll your own out of brass sheet?
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 7:02 pm
by ScaleCraft
Well.....I'd say you may be right. Except: I know folks who did that, to the point of filling in the coupler slot and filing out a space for a Kadee box. Several folk's worth. You see one of them, and think "something is different about the coupler area on that". Ask, and that's what they did. New trucks (when you could still pick up the phone and order such), motor, shafts.....so it may be more prevalent than we think.
One of my 3-rail units came with no end plates whatsoever. Had Lionel electromagnet couplers hanging out the void. One of the forum folks here HAD a set of three rail ends. Now, they came from somewhere, my guess is a 3-2 conversion. And I just did one myself, 2-3. So it happens.
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 7:04 pm
by ScaleCraft
DaveJfr0 wrote:Don't have, but can you measure the thickness and roll your own out of brass sheet?
Maybe. Only critical parts are it must fit around the axles and axle spacing. I am thinking sheet metal. Have some, multiple tin snips (body work stuff), drift punch in the vise, torch, hammer and pliers.
Re: Need GM or A-N NW2 part
Posted: Sat Jul 11, 2020 7:46 pm
by Rufus T. Firefly
ScaleCraft wrote:Well.....I'd say you may be right. Except: I know folks who did that, to the point of filling in the coupler slot and filing out a space for a Kadee box. Several folk's worth. You see one of them, and think "something is different about the coupler area on that". Ask, and that's what they did. New trucks (when you could still pick up the phone and order such), motor, shafts.....so it may be more prevalent than we think.
Yeah, I know yet the 2 rail versions were/are readily available.....
One of my 3-rail units came with no end plates whatsoever. Had Lionel electromagnet couplers hanging out the void. One of the forum folks here HAD a set of three rail ends. Now, they came from somewhere, my guess is a 3-2 conversion. And I just did one myself, 2-3. So it happens.
Yeah, it happened yet the 2 rail versions were and remain relatively common. I've seen partial parts piles for sale for years wondering whatever happened to the res of the body; some got hacked up into whatevers......