.
- Rufus T. Firefly
- Posts: 42227
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: Help With 3 Rail Locomotive Conversion
2railjon wrote:Can anyone share who does 3 Rail locomotive to 2 Rail conversions? It a Weaver 4-4-2 and I have a complete wheel, driver, tender set in 2 Rail from Sunset if that will aid in conversion.
Thanks!
Joe F. who posts here does conversions but those usually entail the creation of drivers. If you can just swap out the drivers, that's the only bit that's got some challenge to it. Rest should be pretty straightforward.
Which 4-4-2?
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: Help With 3 Rail Locomotive Conversion
Weaver model with Sunset parts? Might be a bit more problematic than a screwdriver job.
PM Joe and see what he says.
PM Joe and see what he says.
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:30 pm, edited 1 time in total.
Running that red block Charlie.
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:30 pm, edited 1 time in total.
Running that red block Charlie.
-
bob turner
- Posts: 13675
- Joined: Sat Jan 13, 2007 7:57 pm
Re: Help With 3 Rail Locomotive Conversion
Before getting carried away, disassemble the two, and attempt a trial fit. Weaver and Sunset may be thousands of miles apart, but their Korean builder probably sleeps with himself.
Do you have two complete models, or just the mechanism for the 2-rail?
Do you have two complete models, or just the mechanism for the 2-rail?
Re: Help With 3 Rail Locomotive Conversion
2railjon wrote:Anyone have Joes user name here?
I’m not finding it. Thanks!
Here you go Jon.
rrjjf
Robert
Re: Help With 3 Rail Locomotive Conversion
With regard to using different drivers to convert a 3 rail model to 2 rail operation you will probably have some problems with the crankpins and rods. Most 3 rail "scale" steam model incorporate an odd hollow eccentric crankpin that a metric screws goes through into the driver's crankpin along with some spacers and sleeves. IMO, much easier with a lathe to convert the 3 rail drivers that are made to use with the model's rods to a scale profile.
Joe
Joe
Joe Foehrkolb
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:30 pm, edited 1 time in total.
Running that red block Charlie.
Re: Help With 3 Rail Locomotive Conversion
2RailJohn
I tried reaching you on the phone number you sent to me and got a mechanical message that the phone was not in service.
Joe
I tried reaching you on the phone number you sent to me and got a mechanical message that the phone was not in service.
Joe
Joe Foehrkolb
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:31 pm, edited 1 time in total.
Running that red block Charlie.
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:31 pm, edited 1 time in total.
Running that red block Charlie.
- rex desilets
- Posts: 1786
- Joined: Sun Jul 15, 2007 2:18 pm
Re: Help With 3 Rail Locomotive Conversion
Lovely, lovely cars. Are they scale length?
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” – John Adams
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:32 pm, edited 1 time in total.
Running that red block Charlie.
Re: Help With 3 Rail Locomotive Conversion
.
Last edited by 2railjon on Sun May 27, 2018 5:32 pm, edited 1 time in total.
Running that red block Charlie.
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 60 guests