Page 1 of 2
I'm still laughing................!
Posted: Sat Apr 29, 2017 8:21 pm
by herronpeter
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 8:55 pm
by E7
herronpeter wrote:See why yet??? Peter
No.
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 8:59 pm
by rex desilets
Shipping is free?

Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 9:43 pm
by cole7015
For 4 k starting bid it should be free.
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 10:09 pm
by Jay Criswell
Missing hatches on the sand dome?
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 10:24 pm
by bob turner
I actually followed the various discussions about this model. It had its share of detractors and a very vocal group of true believers. I never figured out its value, so I cannot laugh at this auction.
I suspect that the Bultmann 3- cylinder 4-10-2 is approaching this value on this very limited market. Not sure I think this is out of line. The MMW Diesels will be approaching this price - I cannot believe a Diesel model is as complex as a twelve-coupled 3 cylinder steamer with a booster engine and a tender.
But I have zero expertise, as far as Kohs models are concerned.
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 10:30 pm
by herronpeter
OK, a hint. Spell checker not working at the Kohs Factory.
Peter
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 10:39 pm
by bob turner
And I took you seriously enough to look up the sales price on that Lobaugh Challenger a couple years ago. $2081 or so - I am guessing this thing will sell even with mis-spelled decals.
Re: I'm still laughing................!
Posted: Sat Apr 29, 2017 11:38 pm
by E7
herronpeter wrote:OK, a hint. Spell checker not working at the Kohs Factory.
Peter
Depends on which side of the tender you're looking at! I don't think George does the decaling!
Re: I'm still laughing................!
Posted: Sun Apr 30, 2017 8:49 am
by herronpeter
Still, on a 3600 buck locomotive?? Why was it not fixed when purchased? Or are we going to consider it like the 1969-S Lincoln Cent Double Die Obverse? (29K)
Bob, I never said anything about the price but I guess as most eBay posts are about some ridiculously overpriced item. The only reason I even looked it over was I didn't know Kohs did this model. I also wonder what radius it required to run on a layout!!
Peter
Re: I'm still laughing................!
Posted: Sun Apr 30, 2017 10:14 am
by Rufus T. Firefly
And it's sold.
Re: I'm still laughing................!
Posted: Sun Apr 30, 2017 10:54 am
by E7
herronpeter wrote:Still, on a 3600 buck locomotive?? Why was it not fixed when purchased?
Maybe no one noticed, maybe the owner never unwrapped it, who cares?????!!!!!
herronpeter wrote:Bob, I never said anything about the price but I guess as most eBay posts are about some ridiculously overpriced item. The only reason I even looked it over was I didn't know Kohs did this model. I also wonder what radius it required to run on a layout!! Peter
Price is a relative thing. It may be 4K to you and I, but it's chump change to a lot of folks. Kohs has a list of all his projects on his website:
http://www.kohs.com/Site.htmYou can pretty much make 72" radius the de facto minimum for anything 4-8-4 and up except maybe 3rd Rail stuff, because their 3 rail versions need to navigate way sharper curves.
By, the way, the engine sold.
Re: I'm still laughing................!
Posted: Sun Apr 30, 2017 10:58 am
by up148
I've never heard of one selling for less than $4K, but I've never seen the decal mistake on this loco before either, so anything is possible. Even with it's mistakes, and/or dated electronics, it's a remarkable model of this prototype. Old fashion Dallee sound system requires a 9 volt battery to operate correctly and it has a nightmare wiring harness (just ask Gary Schrader). It was not built with taking it back apart in mind and some items have to be unsoldered to get it apart. Don't you just love it when a builder does that?
Sand dome hatches are attached by chains and most likely inside the dome, but they are next to impossible to get out without doing some paint damage. I owned one for a couple of years. Paid $4k and sold for $4K. It was new and cleaner than this one, but they seldom show up on eBay. I found a NIB early (Mort Mann) 9000 recently for the right price and hope to super detail it, but no way to reach what Kohs imported.
BH
Re: I'm still laughing................!
Posted: Sun Apr 30, 2017 11:09 am
by Rufus T. Firefly
up148 wrote: It was not built with taking it back apart in mind and some items have to be unsoldered to get it apart. Don't you just love it when a builder does that?
I have an old kitbash/scratchbuilt 4-4-0 that was assembled in that fashion.
Re: I'm still laughing................!
Posted: Sun Apr 30, 2017 3:25 pm
by up148
I went back to the listing and it looks like the seller sold numerous Koh's items. Looks like they were listed late last night 9:52 PM PDT and sold this morning. That was fast!!!!!!!!!!!!!!!!! Someone was waiting.
BH