Nice Jay; both the VO chassis/drive and the component inventory,
of all those components I have to ask how those cool chassis-to-can T brackets are made?
also which particular sub-piece(s) are the most labor/problematic to fabricate and how so?
Pete
Accurate O Drive
Re: Accurate O Drive
Political Consultant- Tap into the hidden powers of your public office, insure your future is jail free, well funded. Visit shock and awe upon your adversaries, dominate the media, thrill your followers. contact morbo@happydaysrhereagain.com
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: Accurate O Drive
Pete,
Most of the parts are lost wax castings made to be adapted to what is needed. There are 3 or 4 brackets that can be used as motor mounts or towers. The towers on the trucks were designed to mount to my 1:1 gearboxes and can be cut to length along with being adjustable. One of these times it would probably help to just show the castings.
Most of the parts are lost wax castings made to be adapted to what is needed. There are 3 or 4 brackets that can be used as motor mounts or towers. The towers on the trucks were designed to mount to my 1:1 gearboxes and can be cut to length along with being adjustable. One of these times it would probably help to just show the castings.
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: Accurate O Drive
Attached are a few photos of another project. It will show a few of the castings. This particular model is a later CLW machined frame (very heavy) along with CLW Blomberg trucks but the rest is mine. Think I'm going to like these trucks better than the P&D. Far easier to work with.
Anyway, there are lots of castings and their use depends primarily on the application and motor.
Jay
Anyway, there are lots of castings and their use depends primarily on the application and motor.
Jay
- Attachments
-
- 2018-05-05 013.JPG (1.35 MiB) Viewed 3509 times
-
- 2018-05-05 011.JPG (1.5 MiB) Viewed 3509 times
-
- 2018-05-05 006.JPG (1.29 MiB) Viewed 3509 times
-
- 2018-05-05 005.JPG (1.25 MiB) Viewed 3509 times
-
- 2018-05-05 004.JPG (1.44 MiB) Viewed 3509 times
-
- 2018-05-05 002.JPG (1.42 MiB) Viewed 3509 times
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
-
herronpeter
- Posts: 748
- Joined: Mon Jul 28, 2014 9:13 pm
- Location: Clifton Park, NY
Re: Accurate O Drive
Jay,
What is the gear reduction in that Pittman motor gearhead? How slow can you make this baby run?
Peter
What is the gear reduction in that Pittman motor gearhead? How slow can you make this baby run?
Peter
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: Accurate O Drive
Peter,
It's actually a Faulhaber gear head. Pittman was a little too wide. It's 14:1. One of the primary differences between Jerry's drive and mine is the ability to change ratios. The overall on this model is around 11:1 so it runs a little faster than my usual drives. There's a guy that wants 12, or so, of the heavy CLW retrofitted with my drives but he wants to go faster on the main. Slow speed should still be more than adequate...I hope!
Jay
It's actually a Faulhaber gear head. Pittman was a little too wide. It's 14:1. One of the primary differences between Jerry's drive and mine is the ability to change ratios. The overall on this model is around 11:1 so it runs a little faster than my usual drives. There's a guy that wants 12, or so, of the heavy CLW retrofitted with my drives but he wants to go faster on the main. Slow speed should still be more than adequate...I hope!
Jay
-
Jay Criswell
- Posts: 2004
- Joined: Thu Mar 06, 2008 12:38 pm
Re: Accurate O Drive
Pretty much done with this one. Clean up a little bit of wiring and call it good. Thought I had QSI issues and made it far more complicated than need be. NMRA type plug was partially unplugging itself. On to the Alco, Baldwin, Sac North., etc. Less than two weeks to finish...ugh!




I think we've beat this dead horse and subject to death. Time to move on.
Jay




I think we've beat this dead horse and subject to death. Time to move on.
Jay
Return to “O-Gauge, 2-Rail, Model Railroading”
Who is online
Users browsing this forum: No registered users and 31 guests






