1/72 Coronado flying boat
Re: 1/72 Coronado flying boat
Well the texture of my Supermodel kit is smooth and even.I plan of doing a cammo.job so it is not the concern a natural metal plane would entail.The Rareplanes Stratocruiser had great surface smoothness.
Re: 1/72 Coronado flying boat
What's your technique for painting canopies? Free hand? Masking? Commercially available masking? I've got a 1/144 Bf-110 that's complete except for its canopy. I think free-hand is the only option for that.
Re: 1/72 Coronado flying boat
I normally use blue 3M masking tape.Takes awhile but it is worth it.
Re: 1/72 Coronado flying boat
Another consideration for canopies is to use strips of MicroScale Trim Film. Cut to width and then apply the strips. It's still tedious but not as bad as a 10/0 or 20/0 brush.
I've been using Vallejo's acrylic masking media and I really like it. It dries to a transparent turquoise and is pretty good at leaving the underlying paint alone. On 1/72 planes I've started masking both sides of the canopy, inside full mask and out side just the structural members. On injected molded kits the canopy has enough rigidity that I can apply direct from the bottle and carefully roll the liquid around to only mask the parts I want to stay clear. I then let that dry and then tack the canopy in place on the model with more of the masking media. Let it set and then paint the model. When you are done and the main paint is cured, remove the canopy and with a wooden tooth pick just pick it free in a corner and peel/roll it off. When you've done both sides, use canopy cement to put it on permanently.
I've been using Vallejo's acrylic masking media and I really like it. It dries to a transparent turquoise and is pretty good at leaving the underlying paint alone. On 1/72 planes I've started masking both sides of the canopy, inside full mask and out side just the structural members. On injected molded kits the canopy has enough rigidity that I can apply direct from the bottle and carefully roll the liquid around to only mask the parts I want to stay clear. I then let that dry and then tack the canopy in place on the model with more of the masking media. Let it set and then paint the model. When you are done and the main paint is cured, remove the canopy and with a wooden tooth pick just pick it free in a corner and peel/roll it off. When you've done both sides, use canopy cement to put it on permanently.
Once I built a railroad, I made it run,
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
Made it race against time.
Once I built a railroad, now it's done --
Brother, can you spare a dime?
Re: 1/72 Coronado flying boat
Yes that would work too!
- Rufus T. Firefly
- Posts: 42233
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: 1/72 Coronado flying boat
Now I have to go find an old plane model to build.........

What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: 1/72 Coronado flying boat
Highly Recommended!
- Rufus T. Firefly
- Posts: 42233
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: 1/72 Coronado flying boat
philo426 wrote:Highly Recommended!
I probably have several stashed away; up in the ceiling trusses there's a zeppelin model,
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
- Rufus T. Firefly
- Posts: 42233
- Joined: Wed May 16, 2007 7:52 am
- Location: To be Determined
Re: 1/72 Coronado flying boat
Ok, now you made me climb up on a chair and look - LZ127. Now if I could build it around a bladder for Helium.......
What doesn’t kill you makes you stronger. It also gives you a lot of unhealthy coping mechanisms, trust issues, and a dark sense of humor.
Re: 1/72 Coronado flying boat
Airships are cool!
Return to “The Club Car Lounge”
Who is online
Users browsing this forum: No registered users and 56 guests




